Assembly Instructions The Renard SS24 - Revision history

Wayne J: /* Board Assembly */

2020-12-28T22:56:45Z

Board Assembly

← Older revision		Revision as of 22:56, 28 December 2020
Line 63:		Line 63:
	\|-		\|-
	\|		\|
	* '''12''' - Install the 330 ohm resistor network RN1 (PN# ~~264~~-~~330~~-RC). The resistor network should have a dot on it to indicate pin 1. Insert pin 1 of the resistor network into the square solder pad (to the left).		* '''12''' - Install the 330 ohm resistor network RN1 (PN# 652-4606X-AP1-331LF). The resistor network should have a dot on it to indicate pin 1. Insert pin 1 of the resistor network into the square solder pad (to the left).
	\|\| [[Image:Wiki - Renard SS24 Assembly Step12.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step12.jpg \| 200px]]
	\|-		\|-

Wayne J: /* Parts Listing (BOM) */

2020-12-28T22:48:41Z

Parts Listing (BOM)

← Older revision		Revision as of 22:48, 28 December 2020
Line 254:		Line 254:
	\|align="left"\|Resistor, Carbon Film 180 ohms 1/4W 5%		\|align="left"\|Resistor, Carbon Film 180 ohms 1/4W 5%
	\|-		\|-
	\|~~264~~-~~330~~-RC \|\|1\|\|RN1		\|652-4606X-AP1-331LF \|\|1\|\|RN1
	\|align="left"\|Resistor Network, 6 pin, 330ohms 2%		\|align="left"\|Resistor Network, 6 pin, 330ohms 2%
	\|-		\|-

Wayne J: /* Board Assembly */

2017-01-28T16:02:09Z

Board Assembly

← Older revision		Revision as of 16:02, 28 January 2017
Line 166:		Line 166:
	\|-		\|-
	\|		\|
	* '''34''' - Install two fuses (PN# 504-GMA-10) and two fuse covers (PN# 534-3527C).		* '''34''' - Install two fuses (PN# 504-BK/GMA-10-R) and two fuse covers (PN# 534-3527C).
	\|\| [[Image:Wiki - Renard SS24 Assembly Step34.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step34.jpg \| 200px]]
	\|}		\|}

Wayne J: /* Parts Listing (BOM) */

2017-01-28T16:01:37Z

Parts Listing (BOM)

← Older revision		Revision as of 16:01, 28 January 2017
Line 299:		Line 299:
	\|align="left"\|Shunt		\|align="left"\|Shunt
	\|-		\|-
	\|504-GMA-10\|\|2\|\|F1, F2		\|504-BK/GMA-10-R\|\|2\|\|F1, F2
	\|align="left"\|Fuse, Fast Acting 10A		\|align="left"\|Fuse, Fast Acting 10A
	\|-		\|-

Wayne J: /* Board Assembly */

2015-01-05T00:50:15Z

Board Assembly

← Older revision		Revision as of 00:50, 5 January 2015
Line 152:		Line 152:
	\|-		\|-
	\|		\|
	* '''31''' - Install two RS232/RS485 Interface ICs U4 & U5 (PN# 595-SN65LBC176P).		* '''31''' - Install two RS232/RS485 Interface ICs U4 & U5 (PN# 595-SN65LBC176P ~~ previously ST485BN).
	\|\| [[Image:Wiki - Renard SS24 Assembly Step31.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step31.jpg \| 200px]]
	\|-		\|-

Wayne J: /* Board Assembly */

2015-01-05T00:41:31Z

Board Assembly

← Older revision		Revision as of 00:41, 5 January 2015
Line 100:		Line 100:
	\|-		\|-
	\|		\|
	* '''20''' - Install two 8-pin IC sockets for U4 & U5 (PN# 571-1-~~390261~~-2).		* '''20''' - Install two 8-pin IC sockets for U4 & U5 (PN# 571-1-2199298-2).
	\|\| [[Image:Wiki - Renard SS24 Assembly Step20.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step20.jpg \| 200px]]
	\|-		\|-
	\|		\|
	* '''21''' - Install three 14-pin IC sockets for U6, U7 & U8 (PN# 571-1-~~390261~~-3).		* '''21''' - Install three 14-pin IC sockets for U6, U7 & U8 (PN# 571-1-2199298-3).
	\|\| [[Image:Wiki - Renard SS24 Assembly Step21.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step21.jpg \| 200px]]
	\|-		\|-
	\|		\|
	* '''22''' - Install 25 6-pin IC sockets for U2, M1 thru M24 (PN# 571-1-~~390261~~-1).		* '''22''' - Install 25 6-pin IC sockets for U2, M1 thru M24 (PN# 571-1-2199298-1).
	\|\| [[Image:Wiki - Renard SS24 Assembly Step22.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step22.jpg \| 200px]]
	\|-		\|-
Line 135:		Line 135:
	\|-		\|-
	\|		\|
	* '''28''' - Install the DE9 connector JDP1 (PN# ~~649~~-~~10090099-S094VLF~~).		* '''28''' - Install the DE9 connector JDP1 (PN# 152-3409).
	\|\| [[Image:Wiki - Renard SS24 Assembly Step28.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step28.jpg \| 200px]]
	\|-		\|-
Line 152:		Line 152:
	\|-		\|-
	\|		\|
	* '''31''' - Install two RS232/RS485 Interface ICs U4 & U5 (PN# ~~511~~-~~ST485BN~~).		* '''31''' - Install two RS232/RS485 Interface ICs U4 & U5 (PN# 595-SN65LBC176P).
	\|\| [[Image:Wiki - Renard SS24 Assembly Step31.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step31.jpg \| 200px]]
	\|-		\|-

Wayne J: /* Parts Listing (BOM) */

2015-01-05T00:38:52Z

Parts Listing (BOM)

← Older revision		Revision as of 00:38, 5 January 2015
Line 215:		Line 215:
	\|align="left"\|Crystal Clock Oscillator, 18.432 MHz		\|align="left"\|Crystal Clock Oscillator, 18.432 MHz
	\|-		\|-
	\|~~511~~-~~ST485BN~~ \|\|2\|\|U4, U5		\|595-SN65LBC176P \|\|2\|\|U4, U5
	\|align="left"\|Differential Bus Transceivers		\|align="left"\|Differential Bus Transceivers
	\|-		\|-
	\|571-1-~~390261~~-2\|\|2\|\|		\|571-1-2199298-2\|\|2\|\|
	\|align="left"\|IC Socket, 8 pin (for U4 & U5)		\|align="left"\|IC Socket, 8 pin (for U4 & U5)
	\|-		\|-
Line 224:		Line 224:
	\|align="left"\|PIC Microcontroller		\|align="left"\|PIC Microcontroller
	\|-		\|-
	\|571-1-~~390261~~-3\|\|3\|\|		\|571-1-2199298-3\|\|3\|\|
	\|align="left"\|IC Socket, 14 pin (for U6-U8)		\|align="left"\|IC Socket, 14 pin (for U6-U8)
	\|-		\|-
Line 230:		Line 230:
	\|align="left"\|Optoisolator, Triac Driver		\|align="left"\|Optoisolator, Triac Driver
	\|-		\|-
	\|571-1-~~390261~~-1\|\|25\|\|		\|571-1-2199298-1\|\|25\|\|
	\|align="left"\|IC Socket, 6 pin (for U2, M1-M24)		\|align="left"\|IC Socket, 6 pin (for U2, M1-M24)
	\|-		\|-
Line 287:		Line 287:
	\|align="left"\|Terminal Block, 2 Pos 5.08 mm		\|align="left"\|Terminal Block, 2 Pos 5.08 mm
	\|-		\|-
	\|~~649~~-~~10090099-S094VLF~~\|\|1\|\|JDP1		\|152-3409\|\|1\|\|JDP1
	\|align="left"\| D-Sub Connectors, Right Angle DE9		\|align="left"\| D-Sub Connectors, Right Angle DE9
	\|-		\|-
Line 296:		Line 296:
	\|align="left"\|Header, 2 Pin		\|align="left"\|Header, 2 Pin
	\|-		\|-
	\|~~737~~-~~MSB~~-G\|\|3\|\|		\|806-SX1100-B\|\|3\|\|
	\|align="left"\|Shunt		\|align="left"\|Shunt
	\|-		\|-
Line 313:		Line 313:


	If you are planning on ordering from [http://www.mouser.com Mouser Electronics] you can use this [http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=~~77432d1307~~ Shared Project] to make it easier to order the parts.		If you are planning on ordering from [http://www.mouser.com Mouser Electronics] you can use this [http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=72eedcb487 Shared Project] to make it easier to order the parts.

	==Hardcopy Instructions==		==Hardcopy Instructions==

Wayne J: /* Board Assembly */

2013-11-09T03:29:09Z

Board Assembly

← Older revision		Revision as of 03:29, 9 November 2013
Line 135:		Line 135:
	\|-		\|-
	\|		\|
	* '''28''' - Install the DE9 connector JDP1 (PN# ~~152~~-~~3409~~).		* '''28''' - Install the DE9 connector JDP1 (PN# 649-10090099-S094VLF).
	\|\| [[Image:Wiki - Renard SS24 Assembly Step28.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step28.jpg \| 200px]]
	\|-		\|-

Wayne J: /* Parts Listing (BOM) */

2013-11-09T03:22:34Z

Parts Listing (BOM)

← Older revision		Revision as of 03:22, 9 November 2013
Line 287:		Line 287:
	\|align="left"\|Terminal Block, 2 Pos 5.08 mm		\|align="left"\|Terminal Block, 2 Pos 5.08 mm
	\|-		\|-
	\|~~152~~-~~3409~~\|\|1\|\|JDP1		\|649-10090099-S094VLF\|\|1\|\|JDP1
	\|align="left"\| D-Sub Connectors, Right Angle DE9		\|align="left"\| D-Sub Connectors, Right Angle DE9
	\|-		\|-

Wayne J: /* Board Assembly */

2013-10-26T19:54:40Z

Board Assembly

← Older revision		Revision as of 19:54, 26 October 2013
Line 113:		Line 113:
	\|		\|
	* '''23''' - Install 24 triacs T1 thru T24 (PN# 511-BTA06-600CW). The triacs must be installed correctly. The triac tab/heat sink must be aligned with wider line of the PCB silkscreen outline. The tab/heat sink of the odd numbered triacs will facing the even numbered triacs and vice versa.		* '''23''' - Install 24 triacs T1 thru T24 (PN# 511-BTA06-600CW). The triacs must be installed correctly. The triac tab/heat sink must be aligned with wider line of the PCB silkscreen outline. The tab/heat sink of the odd numbered triacs will facing the even numbered triacs and vice versa.
			**Bolting the triacs to [[Assembly_Instructions_The_Renard_SS24#Triac_Heat_Sink \| the aluminum heat sink]] can act as a good soldering alignment guide.
	\|\| [[Image:Wiki - Renard SS24 Assembly Step23.jpg \| 200px]]		\|\| [[Image:Wiki - Renard SS24 Assembly Step23.jpg \| 200px]]
	\|-		\|-