Pops-O-Matic ESP Programmer - Revision history

Ukewarrior: /* BOM - Bill of Materials */

2020-04-15T22:03:20Z

BOM - Bill of Materials

← Older revision		Revision as of 22:03, 15 April 2020
Line 60:		Line 60:
	- '''R2 A-2203''' - 1/4W carbon or metal film resistor. 10K ohm.<br>		- '''R2 A-2203''' - 1/4W carbon or metal film resistor. 10K ohm.<br>
	- '''R3 A-2203''' - 1/4W carbon or metal film resistor. 10K ohm.<br>		- '''R3 A-2203''' - 1/4W carbon or metal film resistor. 10K ohm.<br>
	- '''R4 A-2282''' - 1/4W carbon or metal film resistor. 560 ohm.Note: this resistor is paired with the POWER LED. You should use ~~o n~~ of the online calculators to determine the most optimal value given a 3.3V input power to your LED.<br>		- '''R4 A-2282''' - 1/4W carbon or metal film resistor. 560 ohm.Note: this resistor is paired with the POWER LED. You should use one of the online calculators to determine the most optimal value given a 3.3V input power to your LED.<br>
	- '''100R''' - There is a resistor labeled 100R to the right of the power switch. It is not needed.<br>		- '''100R''' - There is a resistor labeled 100R to the right of the power switch. It is not needed.<br>
	- '''U1''' - Voltage Regulator, 3.3V, specifically LM2937ET-3.3, TO-220 package.<br>		- '''U1''' - Voltage Regulator, 3.3V, specifically LM2937ET-3.3, TO-220 package.<br>

2020-04-15T22:02:49Z

BOM - Bill of Materials

← Older revision		Revision as of 22:02, 15 April 2020
Line 60:		Line 60:
	- '''R2 A-2203''' - 1/4W carbon or metal film resistor. 10K ohm.<br>		- '''R2 A-2203''' - 1/4W carbon or metal film resistor. 10K ohm.<br>
	- '''R3 A-2203''' - 1/4W carbon or metal film resistor. 10K ohm.<br>		- '''R3 A-2203''' - 1/4W carbon or metal film resistor. 10K ohm.<br>
	- '''R4 A-2282''' - 1/4W carbon or metal film resistor. 560 ohm.<br>		- '''R4 A-2282''' - 1/4W carbon or metal film resistor. 560 ohm.Note: this resistor is paired with the POWER LED. You should use o n of the online calculators to determine the most optimal value given a 3.3V input power to your LED.<br>
	- '''100R''' - There is a resistor labeled 100R to the right of the power switch. It is not needed.<br>		- '''100R''' - There is a resistor labeled 100R to the right of the power switch. It is not needed.<br>
	- '''U1''' - Voltage Regulator, 3.3V, specifically LM2937ET-3.3, TO-220 package.<br>		- '''U1''' - Voltage Regulator, 3.3V, specifically LM2937ET-3.3, TO-220 package.<br>

2019-12-14T19:59:43Z

Errata

← Older revision		Revision as of 19:59, 14 December 2019
Line 92:		Line 92:
	So, the end user doesn't need to do anything to fix this error.<br><br>		So, the end user doesn't need to do anything to fix this error.<br><br>

	Due to this error, the capacitor for C5 must be mounted using the middle and right most holes only. The left most hole is not connected to anything.		Due to this error, the capacitor for C5 must be mounted using the middle and right most holes only. The left most hole is not connected to anything.<br>
			'''This restriction has been removed with the ver1.1 board'''
	<br>		<br>
	This may cause a problem if your C5 capacitor has 5mm spaced leads. In this case, you would either bend the leads to fit the more narrow spacing,<br>		This may cause a problem if your C5 capacitor has 5mm spaced leads. In this case, you would either bend the leads to fit the more narrow spacing,<br>

2019-12-14T19:58:10Z

Errata

← Older revision		Revision as of 19:58, 14 December 2019
Line 86:		Line 86:
	[[Image:Popsomatic_back.jpg\|right\|small]]		[[Image:Popsomatic_back.jpg\|right\|small]]
	The initial board run has one small error.<br><br>		The initial board run has one small error.<br><br>
	This error has been fixed with the ver 1.1 board. (This version number is noted on the back of the board)<br><br>		'''This error has been fixed with the ver 1.1 board.''' (This version number is noted on the back of the board)<br><br>
	There is an unwanted trace on the back of the board that connects the right most pin '''(as viewed from the TOP) '''of part C5 to the ground backplane that covers the bottom of the board.<br>		There is an unwanted trace on the back of the board that connects the right most pin '''(as viewed from the TOP) '''of part C5 to the ground backplane that covers the bottom of the board.<br>
	This unwanted trace should have been placed on the left most pin of C5. <br>		This unwanted trace should have been placed on the left most pin of C5. <br>

2019-12-14T19:57:09Z

Errata

← Older revision		Revision as of 19:57, 14 December 2019
Line 86:		Line 86:
	[[Image:Popsomatic_back.jpg\|right\|small]]		[[Image:Popsomatic_back.jpg\|right\|small]]
	The initial board run has one small error.<br><br>		The initial board run has one small error.<br><br>
			This error has been fixed with the ver 1.1 board. (This version number is noted on the back of the board)<br><br>
	There is an unwanted trace on the back of the board that connects the right most pin '''(as viewed from the TOP) '''of part C5 to the ground backplane that covers the bottom of the board.<br>		There is an unwanted trace on the back of the board that connects the right most pin '''(as viewed from the TOP) '''of part C5 to the ground backplane that covers the bottom of the board.<br>
	This unwanted trace should have been placed on the left most pin of C5. <br>		This unwanted trace should have been placed on the left most pin of C5. <br>

2018-10-25T13:44:13Z

Pops-O-Matic Overview

← Older revision		Revision as of 13:44, 25 October 2018
Line 26:		Line 26:
	4. Mini USB<br>		4. Mini USB<br>
	5. Barrel Terminal Jack<br><br>		5. Barrel Terminal Jack<br><br>
	The board has a power ON/OFF switch with a power ON LED indicator.<br>		The board has a power ON/OFF switch with a power ON LED indicator.<br><br>
			NOTE: <br>
			Input power should be at least 400ma.

	== Order a board ==		== Order a board ==

2018-10-22T13:59:33Z

Pictures of built Pops-O-Matic boards

2018-10-22T13:57:51Z

Pictures of built Pops-O-Matic boards

← Older revision		Revision as of 13:57, 22 October 2018
Line 97:		Line 97:
	== Pictures of built Pops-O-Matic boards ==		== Pictures of built Pops-O-Matic boards ==

			Tyson Howard's build:
			[[File:Pixelpops.jpg]]

			Pops original build:
	[[File:purgeme3.jpg]]		[[File:purgeme3.jpg]]
	[[File:purgeme1.jpg]]		[[File:purgeme1.jpg]]

2018-06-01T02:12:29Z

Disclaimers

← Older revision		Revision as of 02:12, 1 June 2018
Line 33:		Line 33:
	== Disclaimers ==		== Disclaimers ==

	'''USE the ~~ESPixel~~ Pops board at Your Own Risk !'''<br>		'''USE the Pops-O-Matic board at Your Own Risk !'''<br>
	'''The ~~ESPixel~~ Pops board has NO warranty expressed or implied'''		'''The Pops-O-Matic board has NO warranty expressed or implied'''

	== BOM - Bill of Materials ==		== BOM - Bill of Materials ==

2018-02-14T14:54:09Z

Pops-O-Matic Overview

← Older revision		Revision as of 14:54, 14 February 2018
Line 20:		Line 20:
	The Pop-O-Matic is designed to be flexible in assembly and use.<br>		The Pop-O-Matic is designed to be flexible in assembly and use.<br>
	It can take a wide variation of power input voltages (5V-16V) and can support up to 5 different power connections.<br>		It can take a wide variation of power input voltages (5V-16V) and can support up to 5 different power connections.<br>
	The board is designed to use any of the following for a power input connection:<br>		The board is designed to use any of the following for a power input connection types:<br>
	1. 5mm Terminal Block<br>		1. 5mm Terminal Block<br>
	2. 3.5mm Terminal Block<br>		2. 3.5mm Terminal Block<br>