PropController - Revision history

Erm213: /* Tips */

2011-05-28T02:06:07Z

Tips

← Older revision		Revision as of 02:06, 28 May 2011
Line 10:		Line 10:
	* Start by checking the PCB for any obvious faults, missing/broken traces, holes that aren't clear, etc.		* Start by checking the PCB for any obvious faults, missing/broken traces, holes that aren't clear, etc.
	* Clean the PCB with Rubbing Alcohol (atleast 70%) or other PCB cleaner. (Not required, makes things a bit easier though).		* Clean the PCB with Rubbing Alcohol (atleast 70%) or other PCB cleaner. (Not required, makes things a bit easier though).
	* Get your parts together in order of assembly step, and ~~insure~~ you have the correct number of all needed.		* Get your parts together in order of assembly step, and ensure you have the correct number of all needed.

	== Assembling the Board ==		== Assembling the Board ==

Chilloutdocdoc at 00:47, 28 May 2011

2011-05-28T00:47:43Z

← Older revision		Revision as of 00:47, 28 May 2011
Line 5:		Line 5:
	This is in no way shape or form the only way to assemble a PropController.		This is in no way shape or form the only way to assemble a PropController.
	Part Numbers referenced are taken from the Ethernet PropController BOM.		Part Numbers referenced are taken from the Ethernet PropController BOM.
	~~_Issue with VR1/VR2 placement to be updated_~~

	== Tips ==		== Tips ==
Line 16:		Line 15:

	=== Power and Zero Crossing ===		=== Power and Zero Crossing ===



	{\| border="0" cellpadding="10" style="text-align: left;"		{\| border="0" cellpadding="10" style="text-align: left;"
Line 135:		Line 132:
	\|		\|
	* Install the Transistor (Q1) P/N: P2N2222AGOS-ND. Make sure the body of the package lines up with the silkscreen on the PCB.		* Install the Transistor (Q1) P/N: P2N2222AGOS-ND. Make sure the body of the package lines up with the silkscreen on the PCB.
			* Install the .01uF Capicator (C8) P/N: 399-4260-ND. This capacitor has no polarity to worry about.
	\|\|[[Image:25.JPG\|300px]]		\|\|[[Image:25.JPG\|300px]]
	\|-		\|-

Chilloutdocdoc at 17:14, 27 May 2011

2011-05-27T17:14:08Z

@@ Line 72: / Line 72: @@
 * Measure the voltage at the 5V test point. It should be 5V give or take a few hundredths.
 * Measure the voltage at the 3.3V test point. It should be 3.3V give or take a few hundredths.
 === Main Board ===
@@ Line 111: / Line 143: @@
+|
 * Install the four 8-Position Male Headers (J1 - J4) P/N: WM4206-ND. Be sure they sit flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)
 * Install the 12-Position Male Header (J5) P/N: WM8124-ND. Be sure it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)
 * Install the 2-Position Male Header (J13) P/N: WM8072-ND. Be sure that it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)

Chilloutdocdoc at 17:07, 27 May 2011

2011-05-27T17:07:51Z

← Older revision		Revision as of 17:07, 27 May 2011
Line 81:		Line 81:
	* Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note)		* Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note)
	* Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note)		* Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note)
			\|\|[[Image:20.JPG\|300px]]
			\|-
			\|
	* Install the four 150 Ohm 1/4W resistors (R 1, R 5, R 18, R 19) P/N: 150QBK-ND . The color bands are Brown, Green, Brown, Gold. The resistors have no polarity to worry about.		* Install the four 150 Ohm 1/4W resistors (R 1, R 5, R 18, R 19) P/N: 150QBK-ND . The color bands are Brown, Green, Brown, Gold. The resistors have no polarity to worry about.
			* Install the 33k Ohm 1/4W resistor (R 2). P/N: 33KQBK-ND. The color bands are Orange, Orange, Orange, Gold. The resistors have no polarity to worry about.
			\|\|[[Image:21.JPG\|300px]]
			\|-
			\|
	* Install the 220 Ohm 1/4W resistor (R 3). P/N: 220QBK-ND. The color bands are Red, Red, Brown, Gold. The resistors have no polarity to worry about.		* Install the 220 Ohm 1/4W resistor (R 3). P/N: 220QBK-ND. The color bands are Red, Red, Brown, Gold. The resistors have no polarity to worry about.
	* Install the 33k Ohm 1/4W resistor (R 2). ~~P/N: 33KQBK~~-~~ND. The color bands are Orange, Orange, Orange, Gold. The resistors have no polarity to worry about.~~		\|\|[[Image:22.JPG\|300px]]
			\|-
			\|
	* Install the 5MHz Crystal (X1) P/N: XC1711-ND. There is no polarity or orientation to worry about.		* Install the 5MHz Crystal (X1) P/N: XC1711-ND. There is no polarity or orientation to worry about.
			\|\|[[Image:23.JPG\|300px]]
			\|-
			\|
	* Install the 5mm Red/Green LED (L3) P/N: 754-1278-ND (Orientation Note)		* Install the 5mm Red/Green LED (L3) P/N: 754-1278-ND (Orientation Note)
	* Install the Reset Switch (PB1) P/N: 450-1650-ND. (Orientation Note)		* Install the Reset Switch (PB1) P/N: 450-1650-ND. (Orientation Note)
			\|\|[[Image:24.JPG\|300px]]
			\|-
			\|
	* Install the Transistor (Q1) P/N: P2N2222AGOS-ND. Make sure the body of the package lines up with the silkscreen on the PCB.		* Install the Transistor (Q1) P/N: P2N2222AGOS-ND. Make sure the body of the package lines up with the silkscreen on the PCB.
			\|\|[[Image:25.JPG\|300px]]
			\|-
			\|
	* Install the Female Headers P/N: S7078-ND for the WizNet Module. They have no orientation, but make sure they sit flush with the PCB.		* Install the Female Headers P/N: S7078-ND for the WizNet Module. They have no orientation, but make sure they sit flush with the PCB.
			\|\|[[Image:27.JPG\|300px]]
			\|-
			\|
	* Install the four 8-Position Male Headers (J1 - J4) P/N: WM4206-ND. Be sure they sit flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)		* Install the four 8-Position Male Headers (J1 - J4) P/N: WM4206-ND. Be sure they sit flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)
	* Install the 12-Position Male Header (J5) P/N: WM8124-ND. Be sure it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)		* Install the 12-Position Male Header (J5) P/N: WM8124-ND. Be sure it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)

Chilloutdocdoc at 01:51, 24 May 2011

2011-05-24T01:51:04Z

← Older revision		Revision as of 01:51, 24 May 2011
Line 76:		Line 76:

	* Install the Propeller IC (U1) P/N: P8X32A-Q44-ND. (Orientation Note)		* Install the Propeller IC (U1) P/N: P8X32A-Q44-ND. (Orientation Note)
	\|\|[[Image:19.~~jpg~~\|300px]]		\|\|[[Image:19.JPG\|300px]]
	\|-		\|-
	\|		\|

Chilloutdocdoc at 01:45, 24 May 2011

2011-05-24T01:45:21Z

← Older revision		Revision as of 01:45, 24 May 2011
Line 76:		Line 76:

	* Install the Propeller IC (U1) P/N: P8X32A-Q44-ND. (Orientation Note)		* Install the Propeller IC (U1) P/N: P8X32A-Q44-ND. (Orientation Note)
			\|\|[[Image:19.jpg\|300px]]
			\|-
			\|
	* Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note)		* Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note)
	* Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note)		* Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note)

Chilloutdocdoc at 19:35, 23 May 2011

2011-05-23T19:35:47Z

← Older revision		Revision as of 19:35, 23 May 2011
Line 66:		Line 66:
	=== Test the Power ===		=== Test the Power ===

	* to be ~~written~~		* Hook up a power source of 9-12V AC to the terminal block in the bottom right of the board.
			\|\|[[Image:11.jpg\|300px]]
			\|-
			\|
			* Measure the voltage at the 5V test point. It should be 5V give or take a few hundredths.
			* Measure the voltage at the 3.3V test point. It should be 3.3V give or take a few hundredths.

	=== Main Board ===		=== Main Board ===

Chilloutdocdoc at 16:40, 23 May 2011

2011-05-23T16:40:31Z

← Older revision		Revision as of 16:40, 23 May 2011
Line 26:		Line 26:

	* Install four diodes (D1 - D4) P/N: 1N5817DICT-ND. The diodes have a strip (silver/grey) that must line up with the white silkscreen on the PCB.		* Install four diodes (D1 - D4) P/N: 1N5817DICT-ND. The diodes have a strip (silver/grey) that must line up with the white silkscreen on the PCB.
	\|\|[[Image:3.jpg\|300px]]		\|\|[[Image:2.jpg\|300px]]
	\|-		\|-
	\|		\|
Line 34:		Line 34:
	\|		\|
	* Install the three 10k Ohm 1/4W resistors (R 4, R 8, R 22) P/N: 10KQBK-ND. The color bands are (Brown, Black, Orange, Gold). The resistors have no polarity to worry about.		* Install the three 10k Ohm 1/4W resistors (R 4, R 8, R 22) P/N: 10KQBK-ND. The color bands are (Brown, Black, Orange, Gold). The resistors have no polarity to worry about.
			\|\|[[Image:4.jpg\|300px]]
			\|-
			\|

			* Install the 0.1uF capacitor (C13) P/N: 445-2634-ND. This capacitor has no polarity to worry about.
			\|\|[[Image:5.jpg\|300px]]
			\|-
			\|
	* Install the two 47uF capacitors (C2 - C3) P/N: 445-2905-ND. These capacitors have no polarity to worry about.		* Install the two 47uF capacitors (C2 - C3) P/N: 445-2905-ND. These capacitors have no polarity to worry about.
	* Install the four 0.~~1uF capacitor (C4, C7, C9, C13) P/N: 445~~-~~2634-ND. This capacitor has no polarity to worry about.~~		\|\|[[Image:6.jpg\|300px]]
	* Install the 5V Volt Regulator (VR1) P/N: 497-1404-5-ND. The regulator gets installed with the tab attached to the board with the heat-sink sandwiched in the middle. ~~Be careful not~~ to ~~torque~~ the ~~leads too much when bending them~~.		\|-
	* Install the 3.3 Volt Regulator (VR2) P/N: LM2937ET-3.3-ND. The regulator gets installed with the tab attached to the board with the heat-sink sandwiched in the middle. ~~Be careful not~~ to ~~torque~~ the ~~leads too much when bending them~~.		\|
			* Install the 5V Volt Regulator (VR1) P/N: 497-1404-5-ND. The regulator gets installed with the tab attached to the board with the heat-sink sandwiched in the middle. Bend the leads first with a pair of needle nose pliers, then attach the heat sink and voltage regulator to the board before soldering. The regulator should lie flat before being tightened down, otherwise the tab could come off.
			* Install the 3.3 Volt Regulator (VR2) P/N: LM2937ET-3.3-ND. The regulator gets installed with the tab attached to the board with the heat-sink sandwiched in the middle. Bend the leads first with a pair of needle nose pliers, then attach the heat sink and voltage regulator to the board before soldering. The regulator should lie flat before being tightened down, otherwise the tab could come off.
			\|\|[[Image:7.jpg\|300px]]
			\|-
			\|
	* Install the Terminal Block (J12) P/N: ED2600-ND. The terminal block gets installed with the holes facing outward.		* Install the Terminal Block (J12) P/N: ED2600-ND. The terminal block gets installed with the holes facing outward.
			\|\|[[Image:8.jpg\|300px]]
			\|-
			\|
	* Install the 2200uF capacitor (C1) P/N: P5143-ND. The capacitor _does_ have a polarity. The - - - stripe on the side of the capacitor goes into the Negative lead.		* Install the 2200uF capacitor (C1) P/N: P5143-ND. The capacitor _does_ have a polarity. The - - - stripe on the side of the capacitor goes into the Negative lead.
			\|\|[[Image:9.jpg\|300px]]
			\|-
			\|
	* Install the Zero Crossing chip (VO1) P/N: H11AA1M-ND. The chip gets installed with the indent matching the silkscreen and the dot denoting pin one matching the silkscreen. (Note: in the picture, you will see a socket, I prefer to put sockets on most of my chips, personal preference, not required).		* Install the Zero Crossing chip (VO1) P/N: H11AA1M-ND. The chip gets installed with the indent matching the silkscreen and the dot denoting pin one matching the silkscreen. (Note: in the picture, you will see a socket, I prefer to put sockets on most of my chips, personal preference, not required).
			\|\|[[Image:10.jpg\|300px]]
			\|-
			\|

	=== Test the Power ===		=== Test the Power ===

Chilloutdocdoc at 03:29, 23 May 2011

2011-05-23T03:29:41Z

← Older revision		Revision as of 03:29, 23 May 2011
Line 49:		Line 49:

	* Install the Propeller IC (U1) P/N: P8X32A-Q44-ND. (Orientation Note)		* Install the Propeller IC (U1) P/N: P8X32A-Q44-ND. (Orientation Note)
			* Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note)
	* Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note)		* Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note)
	* Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note)
	* Install the four 150 Ohm 1/4W resistors (R 1, R 5, R 18, R 19) P/N: 150QBK-ND . The color bands are Brown, Green, Brown, Gold. The resistors have no polarity to worry about.		* Install the four 150 Ohm 1/4W resistors (R 1, R 5, R 18, R 19) P/N: 150QBK-ND . The color bands are Brown, Green, Brown, Gold. The resistors have no polarity to worry about.
	* Install the 220 Ohm 1/4W resistor (R 3). P/N: 220QBK-ND. The color bands are Red, Red, Brown, Gold. The resistors have no polarity to worry about.		* Install the 220 Ohm 1/4W resistor (R 3). P/N: 220QBK-ND. The color bands are Red, Red, Brown, Gold. The resistors have no polarity to worry about.
	* Install the 33k Ohm 1/4W resistor (R 2). P/N: 33KQBK-ND. The color bands are Orange, Orange, Orange, Gold. The resistors have no polarity to worry about.		* Install the 33k Ohm 1/4W resistor (R 2). P/N: 33KQBK-ND. The color bands are Orange, Orange, Orange, Gold. The resistors have no polarity to worry about.
	* Install the 5MHz Crystal (X1) P/N: XC1711-ND. There is no polarity or orientation to worry about.		* Install the 5MHz Crystal (X1) P/N: XC1711-ND. There is no polarity or orientation to worry about.
	* Install the 3mm Red LED (L1) P/N: 754-1243-ND (Orientation Note)
	* Install the 3mm Green LED (L2) P/N: 754-1242-ND (Orientation Note)
	* Install the 5mm Red/Green LED (L3) P/N: 754-1278-ND (Orientation Note)		* Install the 5mm Red/Green LED (L3) P/N: 754-1278-ND (Orientation Note)
	* Install the Reset Switch (PB1) P/N: 450-1650-ND. (Orientation Note)		* Install the Reset Switch (PB1) P/N: 450-1650-ND. (Orientation Note)
Line 71:		Line 69:
	* Install the 4.7uF capacitor (C6) P/N: 445-2867-ND. This capacitor has no polarity to worry about.		* Install the 4.7uF capacitor (C6) P/N: 445-2867-ND. This capacitor has no polarity to worry about.
	* Install the 0.1uF capacitor (C7) P/N: 445-2634-ND. This capacitor has no polarity to worry about.		* Install the 0.1uF capacitor (C7) P/N: 445-2634-ND. This capacitor has no polarity to worry about.
			* Install the 3mm Red LED (L1) P/N: 754-1243-ND (Orientation Note)
			* Install the 3mm Green LED (L2) P/N: 754-1242-ND (Orientation Note)

	=== USB Connection (Through Hole Option) ===		=== USB Connection (Through Hole Option) ===

	* To Be Written		* To Be Written

Chilloutdocdoc at 21:44, 22 May 2011

2011-05-22T21:44:14Z

← Older revision		Revision as of 21:44, 22 May 2011
Line 9:		Line 9:
	== Tips ==		== Tips ==

	# Start by checking the PCB for any obvious faults, missing/broken traces, holes that aren't clear, etc.		* Start by checking the PCB for any obvious faults, missing/broken traces, holes that aren't clear, etc.
	# Clean the PCB with Rubbing Alcohol (atleast 70%) or other PCB cleaner. (Not required, makes things a bit easier though).		* Clean the PCB with Rubbing Alcohol (atleast 70%) or other PCB cleaner. (Not required, makes things a bit easier though).
	# Get your parts together in order of assembly step, and insure you have the correct number of all needed.		* Get your parts together in order of assembly step, and insure you have the correct number of all needed.

	== Assembling the Board ==		== Assembling the Board ==
Line 17:		Line 17:
	=== Power and Zero Crossing ===		=== Power and Zero Crossing ===

	# Install four diodes (D1 - D4) P/N: 1N5817DICT-ND. The diodes have a strip (silver/grey) that must line up with the white silkscreen on the PCB.
	[[~~File~~:3.jpg\|300px]]
	# Install the two 750 Ohm 1/4W resistors (R 6 - R 7) P/N: 750QBK-ND. The color bands are Violet, Green, Brown, Gold. The resistors have no polarity to worry about.		{\| border="0" cellpadding="10" style="text-align: left;"
	[[~~File~~:3.jpg\|300px]]		!width="300"\|
	# Install the three 10k Ohm 1/4W resistors (R 4, R 8, R 22) P/N: 10KQBK-ND. The color bands are (Brown, Black, Orange, Gold). The resistors have no polarity to worry about.		!width="200"\|
	# Install the two 47uF capacitors (C2 - C3) P/N: 445-2905-ND. These capacitors have no polarity to worry about.		\|-
	# Install the four 0.1uF capacitor (C4, C7, C9, C13) P/N: 445-2634-ND. This capacitor has no polarity to worry about.		\|
	# Install the 5V Volt Regulator (VR1) P/N: 497-1404-5-ND. The regulator gets installed with the tab attached to the board with the heat-sink sandwiched in the middle. Be careful not to torque the leads too much when bending them.
	# Install the 3.3 Volt Regulator (VR2) P/N: LM2937ET-3.3-ND. The regulator gets installed with the tab attached to the board with the heat-sink sandwiched in the middle. Be careful not to torque the leads too much when bending them.		* Install four diodes (D1 - D4) P/N: 1N5817DICT-ND. The diodes have a strip (silver/grey) that must line up with the white silkscreen on the PCB.
	# Install the Terminal Block (J12) P/N: ED2600-ND. The terminal block gets installed with the holes facing outward.		\|\|[[Image:3.jpg\|300px]]
	# Install the 2200uF capacitor (C1) P/N: P5143-ND. The capacitor _does_ have a polarity. The - - - stripe on the side of the capacitor goes into the Negative lead.		\|-
	# Install the Zero Crossing chip (VO1) P/N: H11AA1M-ND. The chip gets installed with the indent matching the silkscreen and the dot denoting pin one matching the silkscreen. (Note: in the picture, you will see a socket, I prefer to put sockets on most of my chips, personal preference, not required).		\|
			* Install the two 750 Ohm 1/4W resistors (R 6 - R 7) P/N: 750QBK-ND. The color bands are Violet, Green, Brown, Gold. The resistors have no polarity to worry about.
			\|\|[[Image:3.jpg\|300px]]
			\|-
			\|
			* Install the three 10k Ohm 1/4W resistors (R 4, R 8, R 22) P/N: 10KQBK-ND. The color bands are (Brown, Black, Orange, Gold). The resistors have no polarity to worry about.
			* Install the two 47uF capacitors (C2 - C3) P/N: 445-2905-ND. These capacitors have no polarity to worry about.
			* Install the four 0.1uF capacitor (C4, C7, C9, C13) P/N: 445-2634-ND. This capacitor has no polarity to worry about.
			* Install the 5V Volt Regulator (VR1) P/N: 497-1404-5-ND. The regulator gets installed with the tab attached to the board with the heat-sink sandwiched in the middle. Be careful not to torque the leads too much when bending them.
			* Install the 3.3 Volt Regulator (VR2) P/N: LM2937ET-3.3-ND. The regulator gets installed with the tab attached to the board with the heat-sink sandwiched in the middle. Be careful not to torque the leads too much when bending them.
			* Install the Terminal Block (J12) P/N: ED2600-ND. The terminal block gets installed with the holes facing outward.
			* Install the 2200uF capacitor (C1) P/N: P5143-ND. The capacitor _does_ have a polarity. The - - - stripe on the side of the capacitor goes into the Negative lead.
			* Install the Zero Crossing chip (VO1) P/N: H11AA1M-ND. The chip gets installed with the indent matching the silkscreen and the dot denoting pin one matching the silkscreen. (Note: in the picture, you will see a socket, I prefer to put sockets on most of my chips, personal preference, not required).

	=== Test the Power ===		=== Test the Power ===
Line 36:		Line 48:
	=== Main Board ===		=== Main Board ===

	# Install the Propeller IC (U1) P/N: P8X32A-Q44-ND. (Orientation Note)		* Install the Propeller IC (U1) P/N: P8X32A-Q44-ND. (Orientation Note)
	# Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note)		* Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note)
	# Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note)		* Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note)
	# Install the four 150 Ohm 1/4W resistors (R 1, R 5, R 18, R 19) P/N: 150QBK-ND . The color bands are Brown, Green, Brown, Gold. The resistors have no polarity to worry about.		* Install the four 150 Ohm 1/4W resistors (R 1, R 5, R 18, R 19) P/N: 150QBK-ND . The color bands are Brown, Green, Brown, Gold. The resistors have no polarity to worry about.
	# Install the 220 Ohm 1/4W resistor (R 3). P/N: 220QBK-ND. The color bands are Red, Red, Brown, Gold. The resistors have no polarity to worry about.		* Install the 220 Ohm 1/4W resistor (R 3). P/N: 220QBK-ND. The color bands are Red, Red, Brown, Gold. The resistors have no polarity to worry about.
	# Install the 33k Ohm 1/4W resistor (R 2). P/N: 33KQBK-ND. The color bands are Orange, Orange, Orange, Gold. The resistors have no polarity to worry about.		* Install the 33k Ohm 1/4W resistor (R 2). P/N: 33KQBK-ND. The color bands are Orange, Orange, Orange, Gold. The resistors have no polarity to worry about.
	# Install the 5MHz Crystal (X1) P/N: XC1711-ND. There is no polarity or orientation to worry about.		* Install the 5MHz Crystal (X1) P/N: XC1711-ND. There is no polarity or orientation to worry about.
	# Install the 3mm Red LED (L1) P/N: 754-1243-ND (Orientation Note)		* Install the 3mm Red LED (L1) P/N: 754-1243-ND (Orientation Note)
	# Install the 3mm Green LED (L2) P/N: 754-1242-ND (Orientation Note)		* Install the 3mm Green LED (L2) P/N: 754-1242-ND (Orientation Note)
	# Install the 5mm Red/Green LED (L3) P/N: 754-1278-ND (Orientation Note)		* Install the 5mm Red/Green LED (L3) P/N: 754-1278-ND (Orientation Note)
	# Install the Reset Switch (PB1) P/N: 450-1650-ND. (Orientation Note)		* Install the Reset Switch (PB1) P/N: 450-1650-ND. (Orientation Note)
	# Install the Transistor (Q1) P/N: P2N2222AGOS-ND. Make sure the body of the package lines up with the silkscreen on the PCB.		* Install the Transistor (Q1) P/N: P2N2222AGOS-ND. Make sure the body of the package lines up with the silkscreen on the PCB.
	# Install the Female Headers P/N: S7078-ND for the WizNet Module. They have no orientation, but make sure they sit flush with the PCB.		* Install the Female Headers P/N: S7078-ND for the WizNet Module. They have no orientation, but make sure they sit flush with the PCB.
	# Install the four 8-Position Male Headers (J1 - J4) P/N: WM4206-ND. Be sure they sit flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)		* Install the four 8-Position Male Headers (J1 - J4) P/N: WM4206-ND. Be sure they sit flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)
	# Install the 12-Position Male Header (J5) P/N: WM8124-ND. Be sure it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)		* Install the 12-Position Male Header (J5) P/N: WM8124-ND. Be sure it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)
	# Install the 2-Position Male Header (J13) P/N: WM8072-ND. Be sure that it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)		* Install the 2-Position Male Header (J13) P/N: WM8072-ND. Be sure that it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary)

	=== USB Connection (SMT Option) ===		=== USB Connection (SMT Option) ===

	# Install the USB Mini Connector (J11) P/N: 732-2109-ND		* Install the USB Mini Connector (J11) P/N: 732-2109-ND
	# Install the FTDI 232 Chip (U5) P/N: 768-1007-1-ND.		* Install the FTDI 232 Chip (U5) P/N: 768-1007-1-ND.
	# Install the 4.7uF capacitor (C6) P/N: 445-2867-ND. This capacitor has no polarity to worry about.		* Install the 4.7uF capacitor (C6) P/N: 445-2867-ND. This capacitor has no polarity to worry about.
	# Install the 0.1uF capacitor (C7) P/N: 445-2634-ND. This capacitor has no polarity to worry about.		* Install the 0.1uF capacitor (C7) P/N: 445-2634-ND. This capacitor has no polarity to worry about.

	=== USB Connection (Through Hole Option) ===		=== USB Connection (Through Hole Option) ===

	* To Be Written		* To Be Written