Renard SS16 Controller Board - Revision history

Wayne J: /* AC Power Connection */

2017-05-10T23:12:58Z

AC Power Connection

← Older revision		Revision as of 23:12, 10 May 2017
Line 277:		Line 277:

	::In the above layout, the right side banks of triacs are powered by jumper wires [blue/green wires] coming from the left side [N 120V] terminal block. This means that both banks of triacs are being powered by the same AC input [orange/black wires].		::In the above layout, the right side banks of triacs are powered by jumper wires [blue/green wires] coming from the left side [N 120V] terminal block. This means that both banks of triacs are being powered by the same AC input [orange/black wires].


			:'''A pictorial "How To" can be found [http://doityourselfchristmas.com/forums/showthread.php?31143-Renard-SS-power-cord-daisy-chain-option here] using Option 3 WITH a daisy chain option.'''



Line 286:		Line 290:

	:::* The size of both fuses together cannot exceed the current handling capability of the AC input [orange/black wires].		:::* The size of both fuses together cannot exceed the current handling capability of the AC input [orange/black wires].



	~~:'''A pictorial "How To" can be found [http://doityourselfchristmas.com/forums/showthread.php?31143-Renard-SS-power-cord-daisy-chain-option here] using Option 3 WITH a daisy chain option.'''~~

	===Connecting Multiple Renard Boards===		===Connecting Multiple Renard Boards===

Wayne J: /* AC Power Connection */

2017-05-10T23:11:45Z

AC Power Connection

← Older revision		Revision as of 23:11, 10 May 2017
Line 277:		Line 277:

	::In the above layout, the right side banks of triacs are powered by jumper wires [blue/green wires] coming from the left side [N 120V] terminal block. This means that both banks of triacs are being powered by the same AC input [orange/black wires].		::In the above layout, the right side banks of triacs are powered by jumper wires [blue/green wires] coming from the left side [N 120V] terminal block. This means that both banks of triacs are being powered by the same AC input [orange/black wires].


	::Key things to remember in this layout are:		::Key things to remember in this layout are:
Line 284:		Line 285:
	:::'''AND'''		:::'''AND'''

	:::* The size of both fuses together cannot exceed the current handling capability of the AC input [orange/black wires].		:::* The size of both fuses together cannot exceed the current handling capability of the AC input [orange/black wires].




			:'''A pictorial "How To" can be found [http://doityourselfchristmas.com/forums/showthread.php?31143-Renard-SS-power-cord-daisy-chain-option here] using Option 3 WITH a daisy chain option.'''

	===Connecting Multiple Renard Boards===		===Connecting Multiple Renard Boards===

Wayne J at 03:51, 2 November 2013

2013-11-02T03:51:26Z

← Older revision		Revision as of 03:51, 2 November 2013
Line 151:		Line 151:


	==AC Power Handling Capability==		=='''AC Power Handling Capability'''==
	===Maximum Input Load===		===Maximum Input Load===
	:The Renard SS16 is divided into two banks of eight triacs. Each bank of triacs is capable of carrying up to 15 amps of current based on the trace width used on the pcb.		:The Renard SS16 is divided into two banks of eight triacs. Each bank of triacs is capable of carrying up to 15 amps of current based on the trace width used on the pcb.

Wayne J: Added assembly to menu

2013-11-02T03:50:30Z

Added assembly to menu

← Older revision		Revision as of 03:50, 2 November 2013
Line 1:		Line 1:
	[[image:Wiki - Renard SS16 Completed Board.jpg\|600px\|right\|x]]		[[image:Wiki - Renard SS16 Completed Board.jpg\|600px\|right\|x]]

	==Introduction==		=='''Introduction'''==

	:The Renard SS16 is a PIC microcontroller based Christmas light controller with 16 solid state relay circuits incorporated into the board. The board design is based on the PIC-based 8-port dimmer concept originally developed by Phil Short. Information on the original concept can be viewed [http://computerchristmas.com/christmas/link-how_to/HowToId-71/Simple_PIC-Based_8-Port_Dimmer here]. Generic information pertaining to current Renard designs (including maximum channel count) can be found on the [[Renard]] wiki page.		:The Renard SS16 is a PIC microcontroller based Christmas light controller with 16 solid state relay circuits incorporated into the board. The board design is based on the PIC-based 8-port dimmer concept originally developed by Phil Short. Information on the original concept can be viewed [http://computerchristmas.com/christmas/link-how_to/HowToId-71/Simple_PIC-Based_8-Port_Dimmer here]. Generic information pertaining to current Renard designs (including maximum channel count) can be found on the [[Renard]] wiki page.
Line 24:		Line 24:


	==Disclaimers==		=='''Disclaimers'''==

	The standard disclaimers pertaining to the information contained on this wiki page are listed [[Disclaimers \| here.]]		The standard disclaimers pertaining to the information contained on this wiki page are listed [[Disclaimers \| here.]]
Line 30:		Line 30:


	==The Board==		=='''The Board'''==

	[[Image:Wiki - Renard SS16 PCB.jpg \| 800px]]		[[Image:Wiki - Renard SS16 PCB.jpg \| 800px]]
Line 49:		Line 49:


	==Circuit Diagram==		=='''Circuit Diagram'''==

	:The schematic diagram can be found [[media:Renard SS16 Schematic.pdf \| here.]]		:The schematic diagram can be found [[media:Renard SS16 Schematic.pdf \| here.]]
Line 114:		Line 114:
	:::* '''ZC''' – Zero Cross signal		:::* '''ZC''' – Zero Cross signal

	==Firmware==		=='''Firmware'''==

	:The PICs ('''U6''' & '''U7''') must be programmed with the correct firmware for the board to operate correctly. There are two types of firmware available: Operational and Diagnostic. The Operational firmware is what you need for normal board operation. The Diagnostic firmware is a troubleshooting aid to use when there are problems with the board.		:The PICs ('''U6''' & '''U7''') must be programmed with the correct firmware for the board to operate correctly. There are two types of firmware available: Operational and Diagnostic. The Operational firmware is what you need for normal board operation. The Diagnostic firmware is a troubleshooting aid to use when there are problems with the board.
Line 137:		Line 137:


	==Powering the Renard SS16==		=='''Powering the Renard SS16'''==

	:Input power requirements: An AC source		:Input power requirements: An AC source
Line 168:		Line 168:
	:The [[Assembly Instructions The Renard SS16#Parts Listing (BOM) \| BOM]] calls for a 10 amp fuse under that assumption that each bank of triacs will be independantly powered by a common/generic extension cord. Most of the common extension cords used by DIYC members are rated for only 13 amps and 13 amp fuses are not commonly found.		:The [[Assembly Instructions The Renard SS16#Parts Listing (BOM) \| BOM]] calls for a 10 amp fuse under that assumption that each bank of triacs will be independantly powered by a common/generic extension cord. Most of the common extension cords used by DIYC members are rated for only 13 amps and 13 amp fuses are not commonly found.

	==Hooking Up the Renard SS16==		=='''Hooking Up the Renard SS16'''==

	===Data Connections===		===Data Connections===
Line 241:		Line 241:


	===AC Power Connection===		==='''AC Power Connection'''===
	:'''Connection Option #1'''		:'''Connection Option #1'''
	[[image:Wiki - Renard SS16 AC Layout1.jpg \| 800px \|center]]		[[image:Wiki - Renard SS16 AC Layout1.jpg \| 800px \|center]]
Line 333:		Line 333:


	==Computer Setup==		=='''Computer Setup'''==

	:'''VIXEN Settings'''		:'''VIXEN Settings'''
Line 348:		Line 348:
	:::*Hold port open during the duration of the sequence execution: Checked		:::*Hold port open during the duration of the sequence execution: Checked

			=='''Assembly Instructions & BOM'''==

			The assembly instructions and complete BOM with links to the Mouser Shared BOM <br>
			[[Assembly Instructions The Renard SS16]]


	==Setup for Beginners and Troubleshooting==		=='''Setup for Beginners and Troubleshooting'''==

	:If you are unsure that you have built your hardware correctly, you should follow the procedures contained in the [[Beginners Setup Guide The Renard SS16 \| Renard SS16 Beginners Setup Guide]]. These procedures will guide you through the steps to help setup the hardware for the first time.		:If you are unsure that you have built your hardware correctly, you should follow the procedures contained in the [[Beginners Setup Guide The Renard SS16 \| Renard SS16 Beginners Setup Guide]]. These procedures will guide you through the steps to help setup the hardware for the first time.
Line 358:		Line 361:
	:If you encounter any problems with your Renard SS16, you can go to the [[Troubleshooting_Guide_The_Renard_SS16 \| Renard SS16 Troubleshooting Guide]]. The troubleshooting guide contains a methodical process to try to isolate problems/malfunctions and gives suggestions of what to do to fix them.		:If you encounter any problems with your Renard SS16, you can go to the [[Troubleshooting_Guide_The_Renard_SS16 \| Renard SS16 Troubleshooting Guide]]. The troubleshooting guide contains a methodical process to try to isolate problems/malfunctions and gives suggestions of what to do to fix them.

	==Related Links==		=='''Related Links'''==
	:[[Beginners Setup Guide The Renard SS16]]		:[[Beginners Setup Guide The Renard SS16]]

Wayne J at 19:26, 26 October 2013

2013-10-26T19:26:13Z

← Older revision		Revision as of 19:26, 26 October 2013
Line 1:		Line 1:
			[[image:Wiki - Renard SS16 Completed Board.jpg\|600px\|right\|x]]

	==Introduction==		==Introduction==

Ravinglunatic: Ravinglunatic moved page The Renard SS16 Controller Board to Renard SS16 Controller Board: to make it easier to find

2013-05-04T22:08:00Z

Ravinglunatic moved page The Renard SS16 Controller Board to Renard SS16 Controller Board: to make it easier to find

← Older revision	Revision as of 22:08, 4 May 2013
(No difference)

Ravinglunatic at 22:28, 22 January 2012

2012-01-22T22:28:43Z

← Older revision		Revision as of 22:28, 22 January 2012
Line 98:		Line 98:
	:::* '''U1''' – LF50CV, 5 VDC Voltage Regulator		:::* '''U1''' – LF50CV, 5 VDC Voltage Regulator
	:::* '''U3''' – ECS-2100AX-18.432MHZ, 18.432 MHz Crystal Clock Oscillator		:::* '''U3''' – ECS-2100AX-18.432MHZ, 18.432 MHz Crystal Clock Oscillator
	:::* '''T1-T16''' – ~~BTA04~~-~~700T, these are gate sensitive triacs that only require 5mA of current on the gate signal. They were selected as a dual use triac for both LEDs and regular incandescent lights.~~		:::* '''T1-T16''' – BTA06-600CW

Ravinglunatic at 06:31, 3 December 2011

2011-12-03T06:31:27Z

← Older revision		Revision as of 06:31, 3 December 2011
Line 114:		Line 114:
	==Firmware==		==Firmware==

	:The PICs ('''U6''' & '''U7''') must be programmed with the ~~latest~~ firmware for the ~~Renard SS16~~ to operate ~~properly~~. The firmware ~~can be found on~~ the ~~[[Renard Firmware]] wiki page~~.		:The PICs ('''U6''' & '''U7''') must be programmed with the correct firmware for the board to operate correctly. There are two types of firmware available: Operational and Diagnostic. The Operational firmware is what you need for normal board operation. The Diagnostic firmware is a troubleshooting aid to use when there are problems with the board.


			:'''Renard SS Operational Firmware:'''

			::*[[media:Renard SS Operational Firmware.asm \| Renard SS Operational Firmware.asm]] – source code that needs to be compiled


			:'''Renard SS Diagnostic Firmware:'''

			::*[[media:Renard SS Diagnostic Firmware.asm \| Renard SS Diagnostic Firmware.asm]] – source code that needs to be compiled

			:::Instructions for using the Renard SS Diagnostic Firmware are located on this [[Renard Diagnostic Firmware Instructions \| wiki page]] or can be downloaded in this [[media:Renard SS Diagnostic Firmware Instructions.pdf \| file]].


			:'''DMX Firmware:'''

			::Since there are many options available with the Renard DMX firmware it is impractical to post a dedicated Renard SS board version here. Users desiring to use DMX should get the firmware [[Renard Firmware \| here]].

Ravinglunatic at 23:38, 26 November 2011

2011-11-26T23:38:07Z

@@ Line 103: / Line 103: @@
 ::'''Jumpers'''
 :::* '''JP1''' – RS232 signal ground.  Install a shunt (jumper) on JP1 when receiving RS232 data.
-:::* '''JP2''' – 120 ohm termination resistor enable.  Normally a shunt will be installed on JP2.  Remove the shunt if you are experiencing problems with incoming data.
+:::* '''JP2''' – 120 ohm termination resistor enable.  Normally a shunt will be installed on JP2 when receiving RS485 data.  Remove the shunt if you are experiencing problems with incoming data.
 :::* '''JP3''' – Diagnostic LEDs enable.  Install a shunt on JP3 to allow the Diagnostic LEDs to function.  During normal operation, you can remove the shunt with no negative impact on board operation.
@@ Line 288: / Line 288: @@
 :::* The total number of Renard boards that can be connected together depends on the event period and the baud rate being used.  More information on the total number of channels capable with Renard systems can be found here [[Renard#Number of Circuits (Channels) | here.]]

Ravinglunatic at 02:11, 10 May 2011

2011-05-10T02:11:15Z

← Older revision		Revision as of 02:11, 10 May 2011
Line 39:		Line 39:

	<center>'''The Renard SS 16 measures 4.1" X 8"'''</center>		<center>'''The Renard SS 16 measures 4.1" X 8"'''</center>


			==='''Board Availability'''===

			:Check the [http://doityourselfchristmas.com/forums/showthread.php?6663-The-Renard-SS-16-is-now-available!-(first-post-is-current-2-19-2011) DIYC Forum] for the latest information concerning board availability.



	==Circuit Diagram==		==Circuit Diagram==
Line 315:		Line 322:

	:[[Troubleshooting_Guide_The_Renard_SS16]]		:[[Troubleshooting_Guide_The_Renard_SS16]]

			:[http://doityourselfchristmas.com/forums/showthread.php?6663-The-Renard-SS-16-is-now-available!-(first-post-is-current-2-19-2011) Board Availability Information]

	:[[Renard Main Page]]		:[[Renard Main Page]]