Assembly Instructions The Renard SS16: Difference between revisions

From doityourselfchristmas.com
Jump to navigation Jump to search
No edit summary
Line 16: Line 16:
|
|


* Start by checking the PCB over for any obvious production faults. Check for traces that end abruptly or have cracks/breaks in them.  Also check that all holes are clear.  
*'''1''' - Start by checking the PCB over for any obvious production faults. Check for traces that end abruptly or have cracks/breaks in them.  Also check that all holes are clear.  
|| [[Image:Wiki - Renard SS16 PCB.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 PCB.jpg | 200px]]
|-
|-
|  
|  
* Install four diodes D1 thru D4 (PN# 625-1N5817-E3).  The diodes will have a silver/grey stripe on a black body. Make sure that this stripe lines up with the stripe on the PCB silk screen (to the left).  
*'''2''' - Install four diodes D1 thru D4 (PN# 625-1N5817-E3).  The diodes will have a silver/grey stripe on a black body. Make sure that this stripe lines up with the stripe on the PCB silk screen (to the left).  
|| [[Image:Wiki - Renard SS16 Assembly Step02.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step02.jpg | 200px]]
|-
|-
|  
|  
* Install two 750 ohm resistors R1 & R2 (PN# 291-750-RC). Make sure that the resistors have a value of 750 ohms (violet/green/brown/gold stripes). These resistors have no polarity to worry about.
*'''3''' - Install two 750 ohm resistors R1 & R2 (PN# 291-750-RC). Make sure that the resistors have a value of 750 ohms (violet/green/brown/gold stripes). These resistors have no polarity to worry about.
|| [[Image:Wiki - Renard SS16 Assembly Step03.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step03.jpg | 200px]]
|-
|-
|  
|  
* Install the 120 ohm resistor R3 (PN# 291-120-RC). Make sure that the resistor has a value of 120 ohms (brown/red/brown/gold stripes). This resistor have no polarity to worry about.
*'''4''' - Install the 120 ohm resistor R3 (PN# 291-120-RC). Make sure that the resistor has a value of 120 ohms (brown/red/brown/gold stripes). This resistor have no polarity to worry about.
|| [[Image:Wiki - Renard SS16 Assembly Step04.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step04.jpg | 200px]]
|-
|-
|  
|  
* Install two 1K ohm resistors R4, R7 (PN# 299-1K-RC). Make sure that the resistors have a value of 1K ohm (brown/black/red/gold stripes). These resistors have no polarity to worry about.  
*'''5''' - Install two 1K ohm resistors R4, R7 (PN# 299-1K-RC). Make sure that the resistors have a value of 1K ohm (brown/black/red/gold stripes). These resistors have no polarity to worry about.  
|| [[Image:Wiki - Renard SS16 Assembly Step05.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step05.jpg | 200px]]
|-
|-
|  
|  
* Install three 27K ohm resistors R5, R8, R9 (PN# 299-27K-RC). Make sure that the resistors have a value of 27K ohms (red/violet/orange/gold stripes). These resistors have no polarity to worry about.  
*'''6''' - Install three 27K ohm resistors R5, R8, R9 (PN# 299-27K-RC). Make sure that the resistors have a value of 27K ohms (red/violet/orange/gold stripes). These resistors have no polarity to worry about.  
|| [[Image:Wiki - Renard SS16 Assembly Step06.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step06.jpg | 200px]]
|-
|-
|  
|  
* Install zener diode D5 (PN# 78-1N5229B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the left).  
*'''7''' - Install zener diode D5 (PN# 78-1N5229B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the left).  
|| [[Image:Wiki - Renard SS16 Assembly Step07.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step07.jpg | 200px]]
|-
|-
|  
|  
* Install zener diode D6 (PN# 78-1N5239B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the right).  
*'''8''' - Install zener diode D6 (PN# 78-1N5239B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the right).  
|| [[Image:Wiki - Renard SS16 Assembly Step08.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step08.jpg | 200px]]
|-
|-
|  
|  
* Install 17 680 ohm resistors R6, R10 thru R25 (PN# 299-680-RC). Make sure that the resistors have a value of 680 ohms (blue/grey/brown/gold stripes). These resistors have no polarity to worry about.  
*'''9''' - Install 17 680 ohm resistors R6, R10 thru R25 (PN# 299-680-RC). Make sure that the resistors have a value of 680 ohms (blue/grey/brown/gold stripes). These resistors have no polarity to worry about.  
|| [[Image:Wiki - Renard SS16 Assembly Step09.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step09.jpg | 200px]]
|-
|-
|  
|  
* Install 16 180 ohm resistors R26 thru R41 (PN# 291-180-RC). Make sure that the resistors have a value of 180 ohms (brown/grey/brown/gold stripes). These resistors have no polarity to worry about.  
*'''10''' - Install 16 180 ohm resistors R26 thru R41 (PN# 291-180-RC). Make sure that the resistors have a value of 180 ohms (brown/grey/brown/gold stripes). These resistors have no polarity to worry about.  
|| [[Image:Wiki - Renard SS16 Assembly Step10.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step10.jpg | 200px]]
|-
|-
|  
|  
* Install two 0.1uF capacitors C3, C4 (PN# 80-C322C104K5R). These capacitors have no polarity to worry about.  
*'''11''' - Install two 0.1uF capacitors C3, C4 (PN# 80-C322C104K5R). These capacitors have no polarity to worry about.  
|| [[Image:Wiki - Renard SS16 Assembly Step11.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step11.jpg | 200px]]
|-
|-
Line 63: Line 63:
|-
|-
|
|
* Install the 330 ohm resistor network RN1 (PN# 264-330-RC). The resistor network should have a dot on it to indicate pin 1. Insert pin 1 of the resistor network into the square solder pad (to the left).  
*'''12''' - Install the 330 ohm resistor network RN1 (PN# 264-330-RC). The resistor network should have a dot on it to indicate pin 1. Insert pin 1 of the resistor network into the square solder pad (to the left).  
|| [[Image:Wiki - Renard SS16 Assembly Step12.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step12.jpg | 200px]]
|-
|-
|
|
* Install four green LEDs PWR (D7), HB, ZC & SD (PN# 604-WP7104GT). The LEDs are polarized and must be installed correctly. The short lead is the cathode and must be placed in the square solder pad.  
*'''13a''' - Install four green LEDs PWR (D7), HB, ZC & SD (PN# 604-WP7104GT). The LEDs are polarized and must be installed correctly. The short lead is the cathode and must be placed in the square solder pad.  
* Install two red LEDs FE & OE (PN# 604-WP7104IT). The LEDs are polarized and must be installed correctly. The short lead is the cathode and must be placed in the square solder pad.  
 
*'''13b''' - Install two red LEDs FE & OE (PN# 604-WP7104IT). The LEDs are polarized and must be installed correctly. The short lead is the cathode and must be placed in the square solder pad.  
|| [[Image:Wiki - Renard SS16 Assembly Step13.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step13.jpg | 200px]]
|-
|-
|  
|  
* Install three 2-pin vertical headers JP1, JP2 & JP3 (PN# 538-22-03-2021).  These headers have no polarity to worry about.  
*'''14''' - Install three 2-pin vertical headers JP1, JP2 & JP3 (PN# 538-22-03-2021).  These headers have no polarity to worry about.  
|| [[Image:Wiki - Renard SS16 Assembly Step14.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step14.jpg | 200px]]
|-
|-
|  
|  
* Install the clock oscillator U3 (PN# 520-TCH1843-X).  The oscillator must be installed in the correct orientation.  The oscillator has three rounded corners and one squared corner, make sure that the squared corner is positioned to match the PCB silkscreen (upper left corner).
*'''15''' - Install the clock oscillator U3 (PN# 520-TCH1843-X).  The oscillator must be installed in the correct orientation.  The oscillator has three rounded corners and one squared corner, make sure that the squared corner is positioned to match the PCB silkscreen (upper left corner).
|| [[Image:Wiki - Renard SS16 Assembly Step15.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step15.jpg | 200px]]
|-
|-
|  
|  
* Install the voltage regulator U1 (PN# 511-LF50CV).  The voltage regulator must be installed correctly.  The voltage regulators tab/heat sink must be aligned with wider line of the PCB silkscreen outline (facing towards the PCB top edge).
*'''16''' - Install the voltage regulator U1 (PN# 511-LF50CV).  The voltage regulator must be installed correctly.  The voltage regulators tab/heat sink must be aligned with wider line of the PCB silkscreen outline (facing towards the PCB top edge).
|| [[Image:Wiki - Renard SS16 Assembly Step16.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step16.jpg | 200px]]
|-
|-
|  
|  
* Install the 2200uF capacitor C1 (PN# 647-UVR1C222MHD1TO). This capacitor is polarized and must be installed correctly. The capacitor should have a black stripe on the body to indicate which lead is negative. The positive lead of the capacitor will be the longer lead. Make sure that the positive lead is placed in the square solder pad.  
*'''17''' - Install the 2200uF capacitor C1 (PN# 647-UVR1C222MHD1TO). This capacitor is polarized and must be installed correctly. The capacitor should have a black stripe on the body to indicate which lead is negative. The positive lead of the capacitor will be the longer lead. Make sure that the positive lead is placed in the square solder pad.  
|| [[Image:Wiki - Renard SS16 Assembly Step17.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step17.jpg | 200px]]
|-
|-
|  
|  
* Install the 47uF capacitor C2 (PN# 647-UVR1C470MDD1TD). This capacitor is polarized and must be installed correctly. The capacitor should have a silver/grey stripe on the body to indicate which lead is negative. The positive lead of the capacitor will be the longer lead. Make sure that the positive lead is placed in the square solder pad.  
*'''18''' - Install the 47uF capacitor C2 (PN# 647-UVR1C470MDD1TD). This capacitor is polarized and must be installed correctly. The capacitor should have a silver/grey stripe on the body to indicate which lead is negative. The positive lead of the capacitor will be the longer lead. Make sure that the positive lead is placed in the square solder pad.  
|| [[Image:Wiki - Renard SS16 Assembly Step18.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step18.jpg | 200px]]
|-
|-
|
|
* Install four fuse clips (PN# 534-3517). '''Note: they are directional for proper fit of the fuse.'''  A helpful installation tip here would be to put a fuse in the clips when you position them in their mounting holes.  This will help keep them correctly aligned so that the fuse will fit properly.
*'''19''' - Install four fuse clips (PN# 534-3517). '''Note: they are directional for proper fit of the fuse.'''  A helpful installation tip here would be to put a fuse in the clips when you position them in their mounting holes.  This will help keep them correctly aligned so that the fuse will fit properly.
    
    
|| [[Image:Wiki - Renard SS16 Assembly Step19.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step19.jpg | 200px]]
Line 100: Line 101:
|-
|-
|  
|  
* Install two 8-pin IC sockets for U4 & U5 (PN# 571-1-390261-2).   
*'''20''' - Install two 8-pin IC sockets for U4 & U5 (PN# 571-1-390261-2).   
|| [[Image:Wiki - Renard SS16 Assembly Step20.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step20.jpg | 200px]]
|-
|-
|  
|  
* Install two 14-pin IC sockets for U6 & U7 (PN# 571-1-390261-3).   
*'''21''' - Install two 14-pin IC sockets for U6 & U7 (PN# 571-1-390261-3).   
|| [[Image:Wiki - Renard SS16 Assembly Step21.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step21.jpg | 200px]]
|-
|-
|  
|  
* Install 17 6-pin IC sockets for U2, M1 thru M16 (PN# 571-1-390261-1).   
*'''22''' - Install 17 6-pin IC sockets for U2, M1 thru M16 (PN# 571-1-390261-1).   
|| [[Image:Wiki - Renard SS16 Assembly Step22.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step22.jpg | 200px]]
|-
|-
|  
|  
* Install 16 triacs T1 thru T16 (PN# 511-BTA04-700T).  The triacs must be installed correctly.  The triac tab/heat sink must be aligned with wider line of the PCB silkscreen outline.  The tab/heat sink of the odd numbered triacs will facing the even numbered triacs and vice versa.
*'''23''' - Install 16 triacs T1 thru T16 (PN# 511-BTA04-700T).  The triacs must be installed correctly.  The triac tab/heat sink must be aligned with wider line of the PCB silkscreen outline.  The tab/heat sink of the odd numbered triacs will facing the even numbered triacs and vice versa.
|| [[Image:Wiki - Renard SS16 Assembly Step23.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step23.jpg | 200px]]
|-
|-
|  
|  
* Install 16 terminal blocks for Ch1 thru Ch16 (PN# 571-2828372).  These terminal blocks have a small interlocking tab that allows the terminals to be "stacked" together to create a larger terminal block.  It is easier to go ahead and "stack" eight terminal blocks together first and then mount them on the PCB.
*'''24''' - Install 16 terminal blocks for Ch1 thru Ch16 (PN# 571-2828372).  These terminal blocks have a small interlocking tab that allows the terminals to be "stacked" together to create a larger terminal block.  It is easier to go ahead and "stack" eight terminal blocks together first and then mount them on the PCB.
|| [[Image:Wiki - Renard SS16 Assembly Step24A.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step24A.jpg | 200px]]


Line 122: Line 123:
|-
|-
|  
|  
* Install two terminal blocks for 120V input (PN# 571-7969492).
*'''25''' - Install two terminal blocks for 120V input (PN# 571-7969492).
|| [[Image:Wiki - Renard SS16 Assembly Step25.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step25.jpg | 200px]]
|-
|-
|  
|  
* Install the transformer TF1 (PN# 838-3FS-312).
*'''26''' - Install the transformer TF1 (PN# 838-3FS-312).
|| [[Image:Wiki - Renard SS16 Assembly Step26.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step26.jpg | 200px]]
|-
|-
|  
|  
* Install two RJ45 modular jacks J1 & J2 (PN# 571-5556416-1).  Due to minor variations in manufacturing, some RJ45 jacks are a tighter fit than others. Care should be taken to ensure that the pins are aligned first before applying too much pressure to seat the locking lugs through the board.  
*'''27''' - Install two RJ45 modular jacks J1 & J2 (PN# 571-5556416-1).  Due to minor variations in manufacturing, some RJ45 jacks are a tighter fit than others. Care should be taken to ensure that the pins are aligned first before applying too much pressure to seat the locking lugs through the board.  
|| [[Image:Wiki - Renard SS16 Assembly Step27.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step27.jpg | 200px]]
|-
|-
|  
|  
* Install the DE9 connector JDP1 (PN# 152-3409).   
*'''28''' - Install the DE9 connector JDP1 (PN# 152-3409).   
|| [[Image:Wiki - Renard SS16 Assembly Step28.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step28.jpg | 200px]]
|-
|-
Line 143: Line 144:
|-
|-
|  
|  
* Install the H11AA1 optocoupler U2 (PN# 782-H11AA1).   
*'''29''' - Install the H11AA1 optocoupler U2 (PN# 782-H11AA1).   
|| [[Image:Wiki - Renard SS16 Assembly Step29.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step29.jpg | 200px]]
|-
|-
|  
|  
* Install two PIC microcontrollers U6 & U7 (PN# 579-PIC16F688-I/P).  The PICs need to be programmed with the appropriate firmware before installation.  More info on programming PICs can be found [http://www.doityourselfchristmas.com/forums/showpost.php?p=3346&postcount=1 here.]
*'''30''' - Install two PIC microcontrollers U6 & U7 (PN# 579-PIC16F688-I/P).  The PICs need to be programmed with the appropriate firmware before installation.  More info on programming PICs can be found [http://www.doityourselfchristmas.com/forums/showpost.php?p=3346&postcount=1 here.]
|| [[Image:Wiki - Renard SS16 Assembly Step30.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step30.jpg | 200px]]
|-
|-
|  
|  
* Install two RS232/RS485 Interface ICs U4 & U5 (PN# 511-ST485BN).
*'''31''' - Install two RS232/RS485 Interface ICs U4 & U5 (PN# 511-ST485BN).
|| [[Image:Wiki - Renard SS16 Assembly Step31.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step31.jpg | 200px]]
|-
|-
|  
|  
* Install 16 optoisolators M1 thru M16 (PN# 859-MOC3023).
*'''32''' - Install 16 optoisolators M1 thru M16 (PN# 859-MOC3023).
|| [[Image:Wiki - Renard SS16 Assembly Step32.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step32.jpg | 200px]]
|-
|-
|  
|  
* Install the heat sink (PN# 532-577102B00) on voltage regulator U1.  The mounting hardware and heat transfer compound are not included in the BOM since any common hardware can be used to attach the heat sink.  If you don't have any heat transfer compound handy, you can use PN# 532-249.  In the picture the heat sink is attached using a #8 x 3/8" metal screw found at home depot.
*'''33''' - Install the heat sink (PN# 532-577102B00) on voltage regulator U1.  The mounting hardware and heat transfer compound are not included in the BOM since any common hardware can be used to attach the heat sink.  If you don't have any heat transfer compound handy, you can use PN# 532-249.  In the picture the heat sink is attached using a #8 x 3/8" metal screw found at home depot.
|| [[Image:Wiki - Renard SS16 Assembly Step33.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step33.jpg | 200px]]
|-
|-
|  
|  
* Install two fuses (PN# 504-GMA-10) and two fuse covers (PN# 534-3527C).
*'''34''' - Install two fuses (PN# 504-GMA-10) and two fuse covers (PN# 534-3527C).
|| [[Image:Wiki - Renard SS16 Assembly Step34.jpg | 200px]]
|| [[Image:Wiki - Renard SS16 Assembly Step34.jpg | 200px]]
|}
|}

Revision as of 02:12, 27 May 2011

Board Assembly

The following sequence of steps is by no means the only way to assemble the Renard SS16. It is simply a suggested order of events to achieve the desired goal.


NOTE: The part numbers referenced in the following instructions are those taken from the Renard SS16 BOM.



  • 1 - Start by checking the PCB over for any obvious production faults. Check for traces that end abruptly or have cracks/breaks in them. Also check that all holes are clear.
  • 2 - Install four diodes D1 thru D4 (PN# 625-1N5817-E3). The diodes will have a silver/grey stripe on a black body. Make sure that this stripe lines up with the stripe on the PCB silk screen (to the left).
  • 3 - Install two 750 ohm resistors R1 & R2 (PN# 291-750-RC). Make sure that the resistors have a value of 750 ohms (violet/green/brown/gold stripes). These resistors have no polarity to worry about.
  • 4 - Install the 120 ohm resistor R3 (PN# 291-120-RC). Make sure that the resistor has a value of 120 ohms (brown/red/brown/gold stripes). This resistor have no polarity to worry about.
  • 5 - Install two 1K ohm resistors R4, R7 (PN# 299-1K-RC). Make sure that the resistors have a value of 1K ohm (brown/black/red/gold stripes). These resistors have no polarity to worry about.
  • 6 - Install three 27K ohm resistors R5, R8, R9 (PN# 299-27K-RC). Make sure that the resistors have a value of 27K ohms (red/violet/orange/gold stripes). These resistors have no polarity to worry about.
  • 7 - Install zener diode D5 (PN# 78-1N5229B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the left).
  • 8 - Install zener diode D6 (PN# 78-1N5239B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the right).
  • 9 - Install 17 680 ohm resistors R6, R10 thru R25 (PN# 299-680-RC). Make sure that the resistors have a value of 680 ohms (blue/grey/brown/gold stripes). These resistors have no polarity to worry about.
  • 10 - Install 16 180 ohm resistors R26 thru R41 (PN# 291-180-RC). Make sure that the resistors have a value of 180 ohms (brown/grey/brown/gold stripes). These resistors have no polarity to worry about.
  • 11 - Install two 0.1uF capacitors C3, C4 (PN# 80-C322C104K5R). These capacitors have no polarity to worry about.
INSTALLATION NOTE:

The following resistor network is a "bussed" type resistor network. This means that the five resistor components (pins 2-6) are all connected in a common buss to pin 1. Installing the resistor network backwards will cause a multitude of malfunctions. So please take the time to make sure it is installed correctly.

  • 12 - Install the 330 ohm resistor network RN1 (PN# 264-330-RC). The resistor network should have a dot on it to indicate pin 1. Insert pin 1 of the resistor network into the square solder pad (to the left).
  • 13a - Install four green LEDs PWR (D7), HB, ZC & SD (PN# 604-WP7104GT). The LEDs are polarized and must be installed correctly. The short lead is the cathode and must be placed in the square solder pad.
  • 13b - Install two red LEDs FE & OE (PN# 604-WP7104IT). The LEDs are polarized and must be installed correctly. The short lead is the cathode and must be placed in the square solder pad.
  • 14 - Install three 2-pin vertical headers JP1, JP2 & JP3 (PN# 538-22-03-2021). These headers have no polarity to worry about.
  • 15 - Install the clock oscillator U3 (PN# 520-TCH1843-X). The oscillator must be installed in the correct orientation. The oscillator has three rounded corners and one squared corner, make sure that the squared corner is positioned to match the PCB silkscreen (upper left corner).
  • 16 - Install the voltage regulator U1 (PN# 511-LF50CV). The voltage regulator must be installed correctly. The voltage regulators tab/heat sink must be aligned with wider line of the PCB silkscreen outline (facing towards the PCB top edge).
  • 17 - Install the 2200uF capacitor C1 (PN# 647-UVR1C222MHD1TO). This capacitor is polarized and must be installed correctly. The capacitor should have a black stripe on the body to indicate which lead is negative. The positive lead of the capacitor will be the longer lead. Make sure that the positive lead is placed in the square solder pad.
  • 18 - Install the 47uF capacitor C2 (PN# 647-UVR1C470MDD1TD). This capacitor is polarized and must be installed correctly. The capacitor should have a silver/grey stripe on the body to indicate which lead is negative. The positive lead of the capacitor will be the longer lead. Make sure that the positive lead is placed in the square solder pad.
  • 19 - Install four fuse clips (PN# 534-3517). Note: they are directional for proper fit of the fuse. A helpful installation tip here would be to put a fuse in the clips when you position them in their mounting holes. This will help keep them correctly aligned so that the fuse will fit properly.
INSTALLATION NOTE:

Pin 1 of the following IC sockets must be aligned with the square solder pad. Another way to verify that you installed them correctly is to make sure that the notch on the socket is aligned with the notch on the PCB silkscreen outline.

  • 20 - Install two 8-pin IC sockets for U4 & U5 (PN# 571-1-390261-2).
  • 21 - Install two 14-pin IC sockets for U6 & U7 (PN# 571-1-390261-3).
  • 22 - Install 17 6-pin IC sockets for U2, M1 thru M16 (PN# 571-1-390261-1).
  • 23 - Install 16 triacs T1 thru T16 (PN# 511-BTA04-700T). The triacs must be installed correctly. The triac tab/heat sink must be aligned with wider line of the PCB silkscreen outline. The tab/heat sink of the odd numbered triacs will facing the even numbered triacs and vice versa.
  • 24 - Install 16 terminal blocks for Ch1 thru Ch16 (PN# 571-2828372). These terminal blocks have a small interlocking tab that allows the terminals to be "stacked" together to create a larger terminal block. It is easier to go ahead and "stack" eight terminal blocks together first and then mount them on the PCB.

  • 25 - Install two terminal blocks for 120V input (PN# 571-7969492).
  • 26 - Install the transformer TF1 (PN# 838-3FS-312).
  • 27 - Install two RJ45 modular jacks J1 & J2 (PN# 571-5556416-1). Due to minor variations in manufacturing, some RJ45 jacks are a tighter fit than others. Care should be taken to ensure that the pins are aligned first before applying too much pressure to seat the locking lugs through the board.
  • 28 - Install the DE9 connector JDP1 (PN# 152-3409).

If you are unsure about your ability to build this board, then you should go to The Beginner's Setup Guide at this point. The Beginner's Setup Guide will walk you thru some initial tests to make sure that everything is working correctly before inserting the IC chips.

INSTALLATION NOTE:

Pin 1 of each IC must be aligned with pin 1 of the corresponding socket. This can be verified by noting that the notch on the IC is aligned with the notch on the socket.

  • 29 - Install the H11AA1 optocoupler U2 (PN# 782-H11AA1).
  • 30 - Install two PIC microcontrollers U6 & U7 (PN# 579-PIC16F688-I/P). The PICs need to be programmed with the appropriate firmware before installation. More info on programming PICs can be found here.
  • 31 - Install two RS232/RS485 Interface ICs U4 & U5 (PN# 511-ST485BN).
  • 32 - Install 16 optoisolators M1 thru M16 (PN# 859-MOC3023).
  • 33 - Install the heat sink (PN# 532-577102B00) on voltage regulator U1. The mounting hardware and heat transfer compound are not included in the BOM since any common hardware can be used to attach the heat sink. If you don't have any heat transfer compound handy, you can use PN# 532-249. In the picture the heat sink is attached using a #8 x 3/8" metal screw found at home depot.
  • 34 - Install two fuses (PN# 504-GMA-10) and two fuse covers (PN# 534-3527C).



Completed Renard SS16



Congratulations! You have finished building your Renard SS16!

Triac Heat Sink

A simple heat sink can be fabricated from .5"x.5"x.060" (1/16”) angle aluminum available at your local home improvement store. You can use a larger size angle if desired, but you have to keep with the 1/16" thickness A template for the hole pattern can be found here. The triac listed in the BOM has an isolated tab, so no isolators are needed.


A small amount of heat transfer compound should be applied between the heat sink and the tab of the triacs. You can use the same compounds that are used on computer CPU chips and their heat sinks. If you don't have any available locally, you can always use something like Mouser PN# 532-249.

Parts Listing (BOM)

IMPORTANT BOM INFORMATION:

Mouser part numbers are listed (unless otherwise noted) as a means of simplifying the listing. Mouser is not the only place to get these parts, they are used as the reference since they tend to have all the parts needed to complete the project. However, the parts can be procured from any electronics parts source that you prefer.

In the event that any of the following parts are not in stock at Mouser when you decide to order them, you can check the Part Substitutions wiki page and see if there any suggestions for alternative parts.


PART NUMBER
(Mouser PN# unless noted)		 QTY REF NOMENCLATURE
511-LF50CV 1 U1 5 VDC Voltage Regulator
532-577102B00 1   Heatsink for Voltage Regulator
782-H11AA1 1 U2 Optocoupler, Bi-Directional Input
520-TCH1843-X 1 U3 Crystal Clock Oscillator, 18.432 MHz
511-ST485BN 2 U4, U5 Differential Bus Transceivers
571-1-390261-2 2   IC Socket, 8 pin (for U4 & U5)
579-PIC16F688-I/P 2 U6, U7 PIC Microcontroller
571-1-390261-3 2   IC Socket, 14 pin (for U6, U7)
859-MOC3023 16 M1-M16 Optoisolator, Triac Driver
571-1-390261-1 17   IC Socket, 6 pin (for U2, M1-M16)
511-BTA04-700T 16 T1-T16 Triac, 4A 700V
291-750-RC 2 R1, R2 Resistor, Carbon Film 750 ohms 1/4W 5%
291-120-RC 1 R3 Resistor, Carbon Film 120 ohms 1/4W 5%
299-1K-RC 2 R4, R7 Resistor, Carbon Film 1K ohms 1/8W 5%
299-27K-RC 3 R5, R8, R9 Resistor, Carbon Film 27K ohms 1/8W 5%
299-680-RC 17 R6, R10-R25 Resistor, Carbon Film 680 ohms 1/8W 5%
291-180-RC 16 R26 – R41 Resistor, Carbon Film 180 ohms 1/4W 5%
264-330-RC 1 RN1 Resistor Network, 6 pin, 330ohms 2%
625-1N5817-E3 4 D1-D4 Diode
78-1N5239B 1 D6 Diode, Zener 9.1V .5W
78-1N5229B 1 D5 Diode, Zener 4.3V .5W
604-WP7104IT 2 FE, OE LED, 3mm Red
604-WP7104GT 4 PWR, HB, ZC, SD LED, 3mm Green
647-UVR1C222MHD1TO 1 C1 Radial Electrolytic Capacitor 16V 2200uF 20%
647-UVR1C470MDD1TD 1 C2 Radial Electrolytic Capacitor 16V 47uF 20%
80-C322C104K5R 2 C3, C4 Capacitor, Radial Ceramic 50V 0.1uF
571-2828372 16 Channel Terminals Terminal Block, 2 Pos 5.08 mm
571-7969492 2 Power Terminals Terminal Block, 2 Pos 5.08 mm
152-3409 1 JDP1 D-Sub Connectors, Right Angle DE9
571-5556416-1 2 J1, J2 Jack, Modular RJ45 PCB Mount Top Entry
538-22-03-2021 3 JP1-JP3 Header, 2 Pin
151-8000 3   Shunt
504-GMA-10 2 F1, F2 Fuse, Fast Acting 10A
534-3517 4   Holder, Fuse Clip PCB mount 5mm
534-3527C 2   Cover, Fuse
838-3FS-312 1 TF1 Power Transformers 12.6VCT@.2A 6.3V@.4A Single Primary


Below is the same parts list as above but it is formatted for direct importing into the Mouser BOM feature. Just copy and paste the list as is. 


511-LF50CV|1
532-577102B00|1
782-H11AA1|1
520-TCH1843-X|1
511-ST485BN|2
571-1-390261-2|2
579-PIC16F688-I/P|2
571-1-390261-3|2
859-MOC3023|16
571-1-390261-1|17
511-BTA04-700T|16
291-750-RC|2
291-120-RC|1
299-1K-RC|2
299-27K-RC|3
299-680-RC|17
291-180-RC|16
264-330-RC|1
625-1N5817-E3|4
78-1N5239B|1
78-1N5229B|1
604-WP7104IT|2
604-WP7104GT|4
647-UVR1C222MHD1TO|1
647-UVR1C470MDD1TD|1
80-C322C104K5R|2
571-2828372|16
571-7969492|2
152-3409|1
571-5556416-1|2
538-22-03-2021|3
151-8000|3
504-GMA-10|2
534-3517|4
534-3527C|2
838-3FS-312|1

Related Links

The Renard SS16 Controller Board
Beginners Setup Guide The Renard SS16
Troubleshooting Guide The Renard SS16
Board Availability Information
Renard Main Page
Renard Firmware
Part Substitutions
VIXEN
Glossary of DIYC Terms
Electronic Symbols
Retrieved from "http://www.doityourselfchristmas.com/wiki/index.php?title=Assembly_Instructions_The_Renard_SS16&oldid=5168"