RENESP Renard ESP8266 WiFi Adapter Group Buy for PCB and BOM

ukewarrior

New member
Group Buy for the low cost ESP8266 based Adapter for Renard Controllers

What does it do?

The RenardESP adapter will convert any Renard that uses the SS BOM (and most of the non - SS models) from a device controlled by RS-485 Serial to a device controlled by e1.31 or sACN over WiFi. It does this by replacing the RS-485 receiver chip on the Renard board.

So instead of running CAT 5 through your yard and connecting your Renards to a RS-485 USB adapter or an e1.31 bridge, you can cut the cords and stream all your control data over wifi.


Group Buy Rules: Read before posting in this thread!

By participating in this Group Buy all participants agree to release www.doityourselfchristmas.com, its Owners, Administrators, Moderators or any other staff of any and all liability and waive all rights I may have under all laws and governing bodies. By posting in this thread you agree you are entering a binding contract between the Organizer (ukewarrior) and the Participant.

Click below to read the rules:
Group Buy Rules
You MUST be a Supporting Member to participate in any Group Buy held on DIYC.



You can become a Supporting member by clicking "Settings" in the upper right of the page, and then "Paid Subscriptions" in the "My Account" menu on the left.
Participation in all Group Buys will require you to be a Supporting member.

Supporting Member has it's perks
:thup:



This Group Buy is for one bare RENESP Board and full BOM



BOM

Description (quantity)

3.3V Regulator (1)
200uF capacitor (1)
0.1uF capacitor (1)
8 pin shrouded socket (1)
8 pin connector (1)
Preci-DIP socket (1)
DIP Adapter (1)
1K Ohm resistor (1)
IDC ribbon cable (12")
2.54 pin header (1)
1N4148 diode (3)
ESP8266 WiFi unit (1)



This Group Buy will end on Nov 15, 2015 at 8pm Eastern US time or sooner if the maximum is reached.


Please note: This Group Buy will be limited to 100 participants or 400 BOMs.


Information Threads
http://doityourselfchristmas.com/forums/showthread.php?40276-RenardESP-Information-Thread&p=398310#post398310
This board was designed by madsci1016


Pricing Info:
The PCB with BOM are $10.65. This does not include shipping; but does include all other fees.

This pricing assumes that at least 100 units are paid for. If less than 100 units are ordered, all money will be refunded and the group buy will be cancelled.

Timing
In order to keep prices down, some of the BOM is being ordered from China. Recent experience has shown that orders can take 30-40 days for delivery.
Therefore, it may be 4-5 weeks from the end of the Group Buy before shipment occurs.

Insurance - is optional, but no responsibility for loss in transit if insurance isn't purchased
$0.01 to $50 - $1.85
$50.01 to $100 - $2.90


Shipping (US)
Do to the vast quantity differences that may be ordered, its impossible to state shipping up front.
Shipping will be done by USPS flat rate priority mail or first class mail if under 13 ounces. Flat rate prices range from $5.30 to $11.15. I will always try to save you money on shipping. If under 13 ounces, they will ship first class mail in a padded envelope to keep costs down.

Canada and outside North America – Additional shipping fees apply. Please note this in your post and I will get you actual shipping costs.
NOTE: I will be shipping to your paypal address. It is very important that you have a correct and compliant USPS address in your paypal profile or your order will be delayed.[\B]

PayPal
US: PayPal fees will be added to your shipping total: $0.30 + 3%
Non-US: PayPal fees will be added: $0.30 + 4%

Payment
1. VERY Important: you MUST put your DIYC username in the comments field within Paypal. If you don't, your order will be rejected and your money immediately returned to you.
2. Post your order in this thread.
3. I will send you a PM with your final total and the PayPal address to send the funds to. Please send payment as a "Goods Payment" so I can ship easier. (see item #1 above!)
4. DO NOT PM ME that you have paid. It is unnecessary and my inbox will fill up.
5. Check post #2 for payment status.

Please post the quantity desired, your country location, and if you want insurance.
 
Group Buy Status Thread:

Status as of 11/20/2015:

I have all payments except for two. You know who you are :whtf:

I have most parts on order and will finish ordering this weekend (assuming all payments are made)


We are at the 100 qty threshold, so everyone can count on this Group Buy Moving Forward !


DIYC name.......Qty.........Payment Status

stenersonj.............4
MindTrik.................2
smohler.................5
Arbo99..................2
JasonPortwood.....3
imbluenote............3
jklingert................8
Xenia....................2
sonic777...............5
Keith R.................2
sparky588...........3
holtm...................2
AuburnLights.......4
nuelemma............2
tkrein...................2
michaelc...............4
mwestling............5
Kev7274..............2
ebrady.................8
algerdes.............10
Bakesbrownies....1
kenoman742.......8
barryiseeu...........4
EMKLLK...............4
MartinMueller2003...3
Hockeyhunter1956...2
cpcoaster.................3
blantrip....................2
gunther...................3
Heldwhat Christmas.....3
bud29.....................6
Rob2791.................4
Don6699................4
slovanredneck........2






total............127
 
Last edited:
i'll try it out, 2016 may be the wireless year. Do you think there may be another buy next year as this is just to try it out, i would need more to go fully wireless next year.

Qty 3.
United States
No insurance
 
I've been planning to tippy toe into wireless - i have a handful of Ren-Ws with XBee that I put together a couple years ago, but never have put in use. This is the first thread i've noticed on this specific RENESP topic, so i haven't read much - can these two approaches coexist? I'm actually planning to test the RenWs this weekend and hopefully incorporate this year, so my question is whether I can supplement those with this RENESP, or if they might work together. I have 6 Ren24SS in use, so i'm definitely interested in reducing the ethernet cables in the yard. I know this is a group-buy thread, so apologies if I should have this question somewhere else, but I'm thinking i will want some of these for next year.
 
Yes, they can coexist. One runs out the serial connection (REN-W) and one runs out the ethernet port.
I've been planning to tippy toe into wireless - i have a handful of Ren-Ws with XBee that I put together a couple years ago, but never have put in use. This is the first thread i've noticed on this specific RENESP topic, so i haven't read much - can these two approaches coexist? I'm actually planning to test the RenWs this weekend and hopefully incorporate this year, so my question is whether I can supplement those with this RENESP, or if they might work together. I have 6 Ren24SS in use, so i'm definitely interested in reducing the ethernet cables in the yard. I know this is a group-buy thread, so apologies if I should have this question somewhere else, but I'm thinking i will want some of these for next year.
 
Back
Top