PropController: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
Line 81: | Line 81: | ||
* Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note) | * Install the 2K EEPROM Chip (U6) P/N: 24AA025E48-I/SN-ND (Orientation Note) | ||
* Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note) | * Install the 512K EEPROM Chip (U2) P/N: 24LC512-I/P-ND (Orientation Note) | ||
||[[Image:20.JPG|300px]] | |||
|- | |||
| | |||
* Install the four 150 Ohm 1/4W resistors (R 1, R 5, R 18, R 19) P/N: 150QBK-ND . The color bands are Brown, Green, Brown, Gold. The resistors have no polarity to worry about. | * Install the four 150 Ohm 1/4W resistors (R 1, R 5, R 18, R 19) P/N: 150QBK-ND . The color bands are Brown, Green, Brown, Gold. The resistors have no polarity to worry about. | ||
* Install the 33k Ohm 1/4W resistor (R 2). P/N: 33KQBK-ND. The color bands are Orange, Orange, Orange, Gold. The resistors have no polarity to worry about. | |||
||[[Image:21.JPG|300px]] | |||
|- | |||
| | |||
* Install the 220 Ohm 1/4W resistor (R 3). P/N: 220QBK-ND. The color bands are Red, Red, Brown, Gold. The resistors have no polarity to worry about. | * Install the 220 Ohm 1/4W resistor (R 3). P/N: 220QBK-ND. The color bands are Red, Red, Brown, Gold. The resistors have no polarity to worry about. | ||
||[[Image:22.JPG|300px]] | |||
|- | |||
| | |||
* Install the 5MHz Crystal (X1) P/N: XC1711-ND. There is no polarity or orientation to worry about. | * Install the 5MHz Crystal (X1) P/N: XC1711-ND. There is no polarity or orientation to worry about. | ||
||[[Image:23.JPG|300px]] | |||
|- | |||
| | |||
* Install the 5mm Red/Green LED (L3) P/N: 754-1278-ND (Orientation Note) | * Install the 5mm Red/Green LED (L3) P/N: 754-1278-ND (Orientation Note) | ||
* Install the Reset Switch (PB1) P/N: 450-1650-ND. (Orientation Note) | * Install the Reset Switch (PB1) P/N: 450-1650-ND. (Orientation Note) | ||
||[[Image:24.JPG|300px]] | |||
|- | |||
| | |||
* Install the Transistor (Q1) P/N: P2N2222AGOS-ND. Make sure the body of the package lines up with the silkscreen on the PCB. | * Install the Transistor (Q1) P/N: P2N2222AGOS-ND. Make sure the body of the package lines up with the silkscreen on the PCB. | ||
||[[Image:25.JPG|300px]] | |||
|- | |||
| | |||
* Install the Female Headers P/N: S7078-ND for the WizNet Module. They have no orientation, but make sure they sit flush with the PCB. | * Install the Female Headers P/N: S7078-ND for the WizNet Module. They have no orientation, but make sure they sit flush with the PCB. | ||
||[[Image:27.JPG|300px]] | |||
|- | |||
| | |||
* Install the four 8-Position Male Headers (J1 - J4) P/N: WM4206-ND. Be sure they sit flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary) | * Install the four 8-Position Male Headers (J1 - J4) P/N: WM4206-ND. Be sure they sit flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary) | ||
* Install the 12-Position Male Header (J5) P/N: WM8124-ND. Be sure it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary) | * Install the 12-Position Male Header (J5) P/N: WM8124-ND. Be sure it sits flush with the PCB. (It is helpful to tack 1 pin down and re-adjust if necessary) |
Revision as of 17:07, 27 May 2011
Assembly Instructions
THIS PAGE IS A WORK IN PROGRESS
This is in no way shape or form the only way to assemble a PropController. Part Numbers referenced are taken from the Ethernet PropController BOM. _Issue with VR1/VR2 placement to be updated_
Tips
- Start by checking the PCB for any obvious faults, missing/broken traces, holes that aren't clear, etc.
- Clean the PCB with Rubbing Alcohol (atleast 70%) or other PCB cleaner. (Not required, makes things a bit easier though).
- Get your parts together in order of assembly step, and insure you have the correct number of all needed.