Search results

*[[Program 2]] *[[Profile 2]] ...

*Once the conversion is complete, click ''Save Conversion Profile''. *Type a name for your saved Conversion Profile and click ''Save.'' ...

...at this point is the ability to manually turn on the first 7 pins (pinout 2 - 8) by clicking on the first port and manually changing the 0's and 1's. | Pin 2 ...

...tutorial, I have already sequenced 8 songs (red highlighted area in Figure 2). '''Figure 2: The Program Management dialog box''' ...

2" Sched 40 PVC Pipe - (10 Feet) 2-in x 1-1/2-in dia PVC Schedule 40 Double Sanitary Tee Fitting - (1) ...

...cted (based on the other boards) instead of the expected location (J4, pin 2), and so forth. The power and ground connections are in the proper and exp 2) The RS232/RS485 connections on pins 4,5 of J1 and J2 are transposed with r ...

Step 2 – [http://www.youtube.com/watch?v=2kbxVwOQ0kg&list=PLaAXWtzVSsm7kkJVcjcLzVU ...4K2YMqGBvo&list=PLaAXWtzVSsm7kkJVcjcLzVUAN5lM9ddy7 Creating a basic Renard profile in Vixen] ...

...f project that provides connectivity between DMX controllers and the Vixen 2.1 lighting software. It was designed by Andrew Williams (LabRat) of Ottawa, ...a handful of components to communicate between the user's PC running Vixen 2.1 and DMX controllers. The design supports full electrical isolation so tha ...

* 2 zip ties (optional) ...the DIP sockets. In addition to adding assembly cost, this will raise the profile of the finished board, possibly making it more difficult to slip a piece of ...

2 299-1K-RC 1K Resistor, 1/8 W, Axial (RS485 series) R4,R7 2 571-5202514 AMP Modular Jacks, Right Angle J3, J4 ...

V1.2 - Initial Release To build the Pixel Extender, you need 2 things: ...

::#:*::#Start the troubleshooting again at step 2. ::#Profile: None ...

...n-W takes input only on pin 4 of J1 connector and ground is made on pins 1-2. You may need to make a special cable by connecting -485 to pin 4 before pl ::Xbee radios operate in the 2.4ghz frequency spectrum, the same spectrum as your wi-fi router or wireless ...

the lowest profile parts first and ending up with the tallest. You can click on any photo to ...ounted either way. '''NOTE: The silkscreen says 680 but the BOM supplies a 2.2K Ohm resistor to work with the full range voltages the board supports. If ...

...<td>511-ST485BN</td><td>Buffers & Line Drivers Hi-Spd Lo Pwr Trans</td><td>2</td></tr> <tr><td>571-1-390261-2</td><td>IC & Component Sockets 8P ECONOMY TIN</td><td>2</td></tr> ...

:::* '''Channel 2 LED''' - will blink ON/OFF to indicate that the PIC is operating correctly. 2 299-750-RC 750 Resistor, 1/8 W, Axial R1,R2 ...

:::• Address 2 means start with channel 17 (skip channels 1-16) ..., we get a start address 2 for the 2nd controller: 17-1= 16, divide 16/8 = 2. ...

#Random Color Code (1,2 for random, any other number then we use your start and end color): #:1=multicolor meteors, 2=random colrs but each meteor is same hue ...

...<td>511-ST485BN</td><td>Buffers & Line Drivers Hi-Spd Lo Pwr Trans</td><td>2</td></tr> <tr><td>571-1-390261-2</td><td>IC & Component Sockets 8P ECONOMY TIN</td><td>2</td></tr> ...

...ound connection since the ground plane is shared between DC IN 1 and DC IN 2. ...<td>511-ST485BN</td><td>Buffers & Line Drivers Hi-Spd Lo Pwr Trans</td><td>2</td></tr> ...